Overmolding: The Complete Guide to Process, Materials and Design

Last Updated: October 20, 2026

Answer Capsule: Overmolding is an injection molding process that molds a second material, usually a soft TPE or TPU, over a finished plastic substrate so the two become one part. A good overmold needs a compatible material pair, a 1 to 3 mm overmold wall, a sharp shut-off and mechanical interlocks where the chemical bond is weak.

Your grip peels off the handle after a month in the field, and the part passed every inspection. That is the overmolding failure engineers fear most, because it shows up after the lot ships. A bad material pair, a feathered edge or a cold substrate turns a two-material part into two loose pieces. The fix usually means a tool change, so you want the design right before anyone cuts steel.

This overmolding guide covers the process and how it differs from insert molding and two-shot molding. It covers which material pairs bond and the design rules that keep the bond. It covers the failures that show up on the shop floor and what the second material adds to cost. The rules come from resin maker design guides, and from what Brent Hanke sees when overmolded parts reach Legacy Molding for DFM review in Phoenix.

What is overmolding?

Overmolding is a two-step injection molding process. A second plastic is molded over a first plastic part, called the substrate, and the two bond into one piece.

The substrate is molded first, usually in a rigid resin like polypropylene, ABS, polycarbonate or nylon. It then goes into a second cavity, or indexes to a second position in a two-shot tool. A soft material is shot over it.

The overmold is almost always a thermoplastic elastomer. TPE, TPV and TPU grades give you a soft grip, a seal, a bumper or a wear surface. No separate rubber part, no assembly step. The bond forms at the melt interface, where the hot overmold softens a thin skin of the substrate and the polymer chains mix.

You will hear two kinds of bond on the shop floor:

  • Chemical bond: the two materials are compatible and the interface fuses. This is the goal for grips and seals.
  • Mechanical lock: the overmold runs through holes, around edges or into undercuts and holds on by shape. This is the backup when the chemistry is weak.

Most good designs use both. Legacy Molding runs overmolding, insert molding and two-shot molding on presses under 200 tons. That covers hand-held housings, tool grips, connectors, seals and brackets. The full range is on the overmolding and insert molding services page.

How is overmolding different from insert molding and two-shot?

Overmolding shoots plastic over a plastic substrate. Insert molding shoots plastic over a metal or other non-plastic insert. Two-shot molding does both shots in one press cycle on one tool. The words get mixed up in quotes and drawings, so here is the split Legacy Molding uses.

Process Substrate Where the second shot happens Best for Tooling
Overmolding (pick and place) Molded plastic part A second, separate mold Grips, seals, moderate volumes Two single-material molds
Insert molding Metal insert, pin, bushing or threaded sleeve One mold; insert loaded before the shot Threads, contacts, shafts One mold with insert locating features
Two-shot molding First shot molded in the same tool Same tool, rotated or core-pulled, same cycle High volume, tight registration, two colors One rotary or core-back mold, two-shot press

The right choice depends on volume, registration and the bond. Pick and place overmolding has the lowest tooling cost and lets you qualify the substrate first. Two-shot gives the best bond and the fastest cycle at volume, because the substrate is still warm for the second shot. The full decision table is in Overmolding vs Insert Molding vs Two-Shot: How to Choose.

Which materials bond in overmolding?

The material pair decides the bond before any design rule does, so pick the pair first. Polarity is the simple test. TPU is polar, so it bonds to polar substrates like polycarbonate, ABS, PC/ABS and nylon. Olefin-based TPEs are non-polar, so they bond to polypropylene but not to polar engineering resins without a special grade.

Substrate Overmold that bonds chemically Notes
Polypropylene (PP) Olefin-based TPE, TPV The classic pair; bonds easily, low cost
ABS, PC, PC/ABS TPU, bonding-grade TPE TPU bonds well; standard TPE needs a grade made for the substrate
Nylon 6 and 66 Nylon-bonding TPE grades, TPU Dry the nylon; a PP-based color carrier can kill the bond
Acetal (POM) Very few; plan on a mechanical lock Low surface energy; design holes and undercuts
Glass-filled resins Same as the base resin Fibers at the surface can weaken the bond, so test it

Specify a TPE grade formulated for your named substrate. A Plastics Technology article on hard-soft overmolding adhesion, written by a GLS elastomer engineer, still holds up. Match the TPE to the substrate, run the melt toward the upper end of the supplier’s range, and keep the substrate clean and free of mold release. Ask your TPE supplier for a peel test on your exact substrate grade, in your color, before you commit to a tool.

Callout: Color matters more than people expect. A color concentrate carried in polypropylene floats to the surface of a nylon substrate and blocks the bond. Specify the carrier resin on the overmold color, not just the Pantone number.

Where does overmolding earn its cost?

Overmolding earns its cost when it replaces an assembly step, a second part or a field failure. If the soft material is there for looks alone, a texture or a paint pass is usually cheaper. Typical jobs where the second shot pays for itself:

  • Grips and handles: hand tools, medical instruments and sporting goods.
  • Seals and gaskets: molded-in lip seals that remove a loose O-ring and an assembly step.
  • Bumpers and wear surfaces: feet, pads and strike faces on industrial equipment.
  • Cable and PCB overmold: strain reliefs and encapsulated boards.
  • Vibration damping: soft isolators molded onto rigid brackets.

Aerospace, defense, medical and electronics OEMs are the usual customers, and Legacy Molding serves all four from Phoenix. Bring their rules on biocompatibility, flammability and traceability into the material pick, not after it.

What are the overmolding design rules that keep the bond?

The design rules all serve one goal: a uniform overmold wall that fills hot, stops at a sharp edge and has somewhere to grab. Here is what Legacy Molding checks on every overmolded part in DFM review.

Overmold thickness: 1 to 3 mm. Avient’s overmolding part design guide calls for 0.060 to 0.120 in (1.5 to 3 mm) for good bonding in most applications. Below about 0.060 in the soft feel disappears, because you feel the hard substrate through it. Thin layers also lose heat so fast the bond never forms. A uniform layer near 0.040 in (1 mm) works where feel is not the point, such as a seal bead.

Shut-offs: sharp, vented and slightly interfering. The shut-off is where the mold steel seals against the substrate to stop the TPE. Design it as a step or a groove, never a feathered taper, because a feathered edge peels. Avient recommends 0.003 to 0.005 in of interference against a plastic substrate to cover shrink and sink. An accent groove about 0.015 to 0.030 in deep by 0.030 to 0.040 in wide gives the shut-off a clean line.

Mechanical interlocks wherever you can fit them. Through-holes, wrap-around edges, dovetails and undercuts let the overmold hold by shape. Use them even when the chemistry is good; they are the safety net when a resin lot or a color changes. Keep them on the substrate, not in the mold, so they do not become side actions.

Draft and radii. Overmold cavities need draft like any other. Avient suggests 3 to 5 degrees on long draws, because soft materials drag. Keep inside radii at 0.020 in or more so the TPE does not tear at a sharp corner.

Venting and gating. Vent the overmold cavity at the end of fill and at every blind pocket, because trapped air shows up as a short shot or a burned bond line. Gate the overmold so the hottest material lands where the bond matters most.

Substrate design. Keep substrate walls uniform and thick enough to resist the second shot’s pressure, or the overmold breaks through or the substrate warps. The general rules on walls, ribs and draft are in the Legacy Molding injection molding design guide.

Why do overmolded parts delaminate, flash or short?

Overmolded parts fail for three reasons: the bond never formed, the shut-off leaked, or the cavity did not fill. Each has a short list of causes. Avient’s troubleshooting guide groups the same three, plus knit lines, sink and warp.

Failure Usual causes Fix
Delamination, peeling Wrong material pair, cold substrate, mold release or oil on the substrate, wet nylon, wrong color carrier, feathered edge Change grade, raise melt and mold temperature, clean or preheat substrates, dry to the supplier’s limit, add interlocks
Flash at the shut-off Poor mold fit, low clamp tonnage, shut-off cut without interference, substrate shrank or sank Blue the tool, raise tonnage or drop pack pressure, recut the shut-off, fix the substrate wall
Short shot in thin overmold Overmold too thin, no vents, gate too far, melt too cold Thicken to 1 mm or more, add vents, move the gate, raise melt temperature

Moisture is the quiet killer. The Plastics Technology article above puts the limit for hygroscopic substrates at 0.05 percent moisture or less before overmolding. Nylon and polycarbonate both drink water, and steam at the interface leaves a bond with nothing holding it. Ask your molder how the substrates were dried and whether they were overmolded the same shift they were molded.

What does overmolding cost compared to a single-shot part?

An overmolded part costs more than the same part in one material. You pay for a second tool or a two-shot tool and a second shot of cycle time. In pick and place you also pay the labor to load substrates.

  • Tooling. Pick and place needs two molds. The second follows the same price ranges as any tool, roughly $3,000 for a simple aluminum tool to $100,000 or more for hardened multi-cavity steel. A two-shot tool costs more than either, because it carries both cavities and the rotation or core-back mechanism.
  • Cycle time. The overmold shot adds its own fill, pack and cool time. Thick TPE walls cool slowly, which is one more reason to hold the 1 to 3 mm rule.
  • Labor and handling. Loading substrates by hand adds seconds per cycle and a chance of a misloaded part. Two-shot removes that, which is why it wins at high volume.

When not to overmold. Skip it when the soft feature is cosmetic only, when the volume is too low to pay back a second tool, or when an O-ring or a stuck-on pad meets the spec. Skip it when the two materials will not bond and you cannot fit an interlock. A good molder tells you that in the DFM review, not after the tool is built. Legacy Molding quotes overmolded parts in 24 to 48 business hours, with 3 to 5 business days for complex DFM.

What an overmolding DFM review catches

Here is a call Legacy Molding gets most months. A design engineer has a hand-held housing with a TPE grip that peels at the edge after a few weeks in the field. The overseas molder blames the TPE supplier, the supplier blames the process, and the engineer has a launch date.

The CAD tells the story in ten minutes. The grip edge tapered to zero thickness, so the TPE feathered out and peeled from the thin end. The substrate was ABS and the TPE was a general purpose olefin grade with no bonding package, so nothing held it but friction. There were no through-holes or wrap-around features on the grip.

The fix is a design change, not a process change. It needs a stepped shut-off with an accent groove, a bonding-grade TPE matched to ABS, two through-holes under the grip, and a uniform 1.5 mm overmold wall. The substrate tool needs a minor recut and the overmold cavity a new insert. Legacy Molding samples the revised tool, runs a first article on both shots and ships the FAI report and material certs with the first lot.

Frequently Asked Questions

Is overmolding expensive?

Overmolding costs more than a single-material part. It needs a second mold or a two-shot mold, a second shot of cycle time and, for pick and place, labor to load substrates. It is cheaper than molding two parts and assembling them once the volume pays back the second tool.

Can you overmold onto metal?

Yes, but that is called insert molding, and the plastic holds the metal by shape rather than by a chemical bond. Knurls, grooves, holes and undercuts on the insert do the work. Overmolding in the strict sense means plastic over a plastic substrate, where a chemical bond is possible.

How thick should an overmold be?

Plan on 1 to 3 mm, or about 0.040 to 0.120 in. Avient’s design guide gives 0.060 to 0.120 in for good bonding, and layers under 0.060 in lose their soft feel. Keep the thickness uniform, because thick spots sink and thin spots short.

Does TPE bond to polypropylene?

Olefin-based TPE and TPV bond well to polypropylene, and that pairing is the most common in overmolding. Standard TPE does not bond to polycarbonate, ABS or nylon. Those need a TPU or a TPE grade made for that substrate, plus a mechanical lock for backup.

Conclusion

Three things decide an overmolded part: the material pair, the overmold wall and the shut-off. Pick a TPE or TPU made for your substrate and hold the overmold between 1 and 3 mm. End it at a sharp stepped shut-off with a through-hole or wrap for backup. Get those right in DFM and the bond holds in the field and the tool cuts once.

Brent Hanke reviews every overmolded part for manufacturability before tooling, and Legacy Molding runs production in Phoenix on presses under 200 tons. Send your CAD and annual volume for a quote with DFM notes, or call Brent at 480-256-9773.

Sources

Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com

Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.

Have a part like this to quote?

Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.

Request a Quote

Similar Posts