Hot Runner vs Cold Runner Molds: Cost, Cycle Time and Fit
Last Updated: November 3, 2026
Answer Capsule: Hot runner vs cold runner is a volume and resin decision. A cold runner mold is cheaper to build but solidifies a sprue and runner with every shot, which costs material and cooling time. A hot runner keeps the melt hot to the gate, so only the part comes out, at a higher tool price.
Your mold quote has a line you did not ask for: “hot runner system, 4 drops, controller extra.” Pick cold when you should have picked hot, and you pay for runner scrap and slow cycles on every shot for years. Pick hot when you should have picked cold, and you pay up front for a system that fights every color change.
Hot runner vs cold runner is one of the few tooling choices that changes both the mold price and the part price. This post explains how each runner works, what the premium buys, where the savings come from, when the math flips, and what Legacy Molding asks before quoting. Brent Hanke’s short answer: at the volumes most Legacy Molding customers run, a cold runner with regrind usually wins. The exceptions are easy to spot.
What is the difference between a hot runner and a cold runner mold?
The difference is whether the plastic in the feed channels solidifies with each shot. In a cold runner mold, the melt travels down a sprue, along runners cut into the parting line, and through a gate into each cavity. The part comes out with a sprue and runner attached, and an operator or a sprue picker separates them.
In a hot runner mold, a heated manifold inside the mold carries the melt to heated nozzles that end at the gate. The runner never freezes, so each shot produces only parts, with a small gate vestige.
The system needs heaters, thermocouples, wiring and a temperature controller beside the press. Plastics Technology’s tooling columnist Randy Kerkstra notes that hot runners eliminate the cold sprue and runner and save scrap when regrind is not an option. They also “add some complexity to the mold and require added maintenance.”
| Factor | Cold runner | Hot runner |
|---|---|---|
| Tool cost | Lower; runner is machined into the plates | Higher; manifold, nozzles, heaters and controller added |
| Material per shot | Part plus sprue and runner | Part only, plus a small vestige |
| Cycle time | Runner is often thicker than the part and sets cooling | Shorter; only the part cools |
| Color and resin changes | Fast; purge the barrel and go | Slower; manifold and nozzles must be purged |
| Maintenance | Simple | Heaters, thermocouples and tips to service |
| Moving the tool | Mold only | Mold plus controller, cables and setup sheets |
| Best fit | Low to mid volume, many colors, resins that regrind well | High volume, costly resins, thin small parts, cosmetic gates |
How much does a hot runner add to mold cost?
A hot runner adds a manifold, one heated nozzle per drop, heaters, thermocouples, wiring and a controller. As a general range, the premium runs thousands of dollars for a small single-drop system and tens of thousands for a high-drop valve-gated manifold. The exact number depends on drop count, valve gates versus thermal gates, and whether the controller is included.
Legacy Molding asks the tool builder to list the hot runner system and the controller as separate lines. Then you can see the premium against the cold runner version of the same tool. The post on what a production injection mold costs covers what else belongs on that itemized quote.
What do you save with a hot runner?
You save the runner material on every shot and the cooling time the runner needed. Plastics Technology’s tipping-point article works a 64-cavity cold runner mold making 2 gram parts. The runner weighed 192 grams on a 320 gram shot, so about 60 percent of every shot went to regrind.
A hot runner was projected to cut the cycle from 14 to 10 seconds. That is an extreme case, but it shows the direction.
Here is the math to run with your own numbers, with the assumptions labeled:
- Runner scrap per year. Runner weight per shot times annual shots times resin price. Example: a 4-cavity tool with a 30 gram runner making 250,000 parts a year is 62,500 shots and about 1,875 kg of runner. At an assumed $1.50 per pound for ABS, that is about $6,200 of resin a year if scrapped.
- Cycle time per year. Seconds saved per shot times annual shots times the press rate. Example: 3 seconds saved on 62,500 shots is about 52 press hours. At an assumed $40 per hour, that is about $2,100.
In this example the savings run about $8,000 a year against the hot runner premium and its extra maintenance. A premium in the low five figures pays back in a year or two; one at the high end does not. Change the resin to a $5 per pound engineering grade and the scrap line alone jumps past $20,000. That is the flip point.
Legacy Molding’s rule: If runner scrap plus cycle savings pays the hot runner premium inside two years at the volume you will actually run, buy the hot runner. If it needs five years of volume you have not sold yet, build cold and regrind.
Can you just regrind the cold runner?
Often yes, and that is what keeps cold runner tools economical, but regrind has limits set by the resin and by your spec. Every pass through the barrel adds heat history, and nylon and polycarbonate lose properties faster than polypropylene or polyethylene.
Most resin makers publish a regrind limit in their processing guide. It is often in the 20 to 25 percent range for commodity resins, and lower for nylon and PC. Some medical and aerospace specs allow none. Ask your resin supplier for the limit on your grade before you count the runner as free.
When regrind is not allowed, the runner is pure scrap and the hot runner case gets much stronger. When it is allowed, Legacy Molding runs it at a controlled ratio, tracks it against the lot, and notes it with the material certification.
When does a cold runner still win?
A cold runner wins on short runs, frequent color changes, development tools, and parts where flexibility matters more than gate cosmetics. Here is a situation Legacy Molding sees a few times a year. A buyer transfers in a hot runner tool from a molder that closed, and the controller did not come with it.
The tool sits until a matching controller is sourced or the manifold is rewired, which can take weeks. The same part in a cold runner tool would have sampled the week it arrived.
That is an argument for owning the controller and the wiring diagrams, which the injection mold tooling and transfer page covers. Cold runner also wins when:
- You run the same tool in several colors; purging a manifold between colors wastes time and resin.
- Annual volume is in the tens of thousands, not hundreds of thousands.
- The part may still change; a cold runner is cheap to modify.
Hot runner vs cold runner: how does Legacy Molding decide?
Legacy Molding runs the scrap and cycle math at your real volume. Then it adds the practical factors: color count, regrind allowance, resin price and how often the tool will move. The injection molding tooling explainer covers the other two levers on the quote, mold class and cavity count.
Legacy Molding designs molds in-house and builds them through vetted tooling partners, so both versions of the tool get priced when the volume is near the flip point. Brent Hanke walks the buyer through both numbers on the same call.
How many parts a year, for how many years? What does the resin cost per pound, and is regrind allowed? How many colors will this tool run?
If the answers are “a million, five years, $4 a pound, one color,” the hot runner pays. If they are “40,000, maybe, ABS, four colors,” build cold.
Frequently Asked Questions
Is a hot runner mold more expensive than a cold runner mold?
Yes. A hot runner adds a heated manifold, nozzles, heaters, wiring and a controller, so the tool costs more up front and needs more maintenance. That is why hot runner vs cold runner is a volume and resin decision rather than a quality one.
Can you change colors on a hot runner mold?
You can, but it takes longer than on a cold runner because the manifold and every nozzle must be purged of the old color. Raise the manifold temperature, purge with a commercial purging compound, and plan for the time. If you run many colors on one tool, a cold runner is usually the better fit.
What happens to a hot runner tool when it moves to a new molder?
The mold, the controller, the cables and the wiring diagram all have to move together. Without the controller, the receiving molder cannot sample the tool. Put the controller in the tooling agreement and ship it with the mold.
Conclusion
Three takeaways: a cold runner is cheaper to build and a hot runner is cheaper to run; the flip point is set by annual shots, runner weight and resin price; and color changes, regrind rules and tool transfers tip the practical side. Legacy Molding prices both when the answer is close.
Ready to see both numbers for your part? Send your CAD and annual volume for a quote with DFM notes →. Questions? Call Brent: 480-256-9773.
Sources
- https://www.ptonline.com/articles/running-cold-to-hot-tipping-point-to-convert-to-a-hot-runner-system
- https://ptonline.com/articles/tooling-hot-runners-a-view-from-the-bottom-up
Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com
Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.
Have a part like this to quote?
Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.
