Injection Molding Tooling Explained: Classes, Cavities, Life
Last Updated: October 29, 2026
Answer Capsule: Injection molding tooling is the steel or aluminum mold that forms your part: cavity, core, runner, gates, ejectors and cooling lines in a mold base. SPI/PLASTICS grades molds from Class 101, hardened steel rated for one million cycles or more, down to Class 105 prototypes rated under 500. Class, cavity count and runner type set the price.
You are about to spend $25,000 to $80,000 on a block of steel, and the quote describes it in words you have never had to price before: Class 101, four-cavity, hot runner, H13 inserts, P20 base. Get the class wrong and you buy a tool that wears out halfway through the program, or one built to run a million parts when you need 50,000. Get the runner wrong and you throw away plastic on every shot for years.
This guide explains injection molding tooling from the inside out: the parts of a mold, the SPI/PLASTICS mold classes, and how cavity count, runner type and steel grade change the price and life of the tool, who builds it, and how to keep it running. Legacy Molding designs molds and runs DFM in-house in Phoenix and builds the steel through vetted tooling partners. This is the walk-through Brent Hanke gives a buyer before a tool quote goes out.
What is injection molding tooling?
Injection molding tooling is the mold: two steel or aluminum halves that close under clamp pressure, fill with molten plastic, cool, open and push your part out, thousands of times a day. “Tooling” covers the mold itself plus everything bolted into it:
- Cavity and core. The cavity forms the outside of your part and the core forms the inside.
- Mold base. The steel frame that holds cavities, cores and everything else, and bolts to the press platens.
- Sprue, runner and gate. The channels that carry melt from the press nozzle to the cavity. The gate is the last, smallest opening, and its location leaves a mark and sets how the part fills.
- Ejector system. Pins, sleeves or stripper plates that push the cooled part off the core.
- Cooling lines. Drilled water channels that pull heat out of the steel. Cooling is most of the cycle, so these lines set your cycle time.
- Side actions. Slides, lifters and cams that form undercuts and pull clear before ejection.
- Vents. Thin grooves at the parting line that let air escape ahead of the melt.
Every one of these is a cost driver and a quality driver. A gate in the wrong spot leaves a weld line across a cosmetic face, and a cooling line that misses a thick boss leaves a sink mark. That is why Legacy Molding reviews the part and the mold design together before any steel is cut, as the injection mold tooling page describes.
What do the SPI/PLASTICS mold classes 101 to 105 mean?
The SPI/PLASTICS mold classes are five life ratings that tell you how many cycles a mold is built to survive, from Class 101 at one million cycles or more down to Class 105 at fewer than 500. They come from the Plastics Industry Association’s Customs and Practices of the Moldmaking Industry guide, last revised in May 2023, written so buyers and mold builders mean the same thing when they say “production tool.”
| Class | Rated life | Typical build | Typical use |
|---|---|---|---|
| 101 | 1,000,000 cycles or more | Hardened tool steel, about 48 HRC or harder, wear plates on slides | High volume, multi-cavity, abrasive resins |
| 102 | Roughly 500,000 to 1,000,000 cycles | Hardened steel, fewer extras | Medium to high volume |
| 103 | Under 500,000 cycles | Prehardened steel such as P20 | Mid-volume programs |
| 104 | Under 100,000 cycles | Aluminum or soft steel | Low volume, bridge tooling |
| 105 | Under 500 cycles | Aluminum, cast or epoxy | Prototypes |
Which class do you need? Divide your expected program life, not one year’s volume, by the parts per cycle. A 200,000 part program in a two-cavity tool is 100,000 cycles, a Class 103 job; the same volume for five years is 500,000 cycles and calls for Class 102 or 101. Glass-filled nylon abrades a soft cavity far faster than ABS, which pushes you up a class at the same volume.
The class also sets the steel. Prehardened P20, delivered at about 28 to 32 HRC, needs no heat treat after machining and is the all-round Class 103 steel, though glass-filled resins wear it. H13 and S7 are hardened to about 48 to 52 HRC for Class 101 and 102 work, abrasive or hot resins, and thin inserts that must not chip. 420 stainless resists corrosion and takes a high polish for clear and cosmetic parts, and aluminum cuts fast and cools fast for Class 104 and 105 tools. Most molds mix materials, such as a P20 base with H13 inserts at the gate, and the steel should be stated on the quote, not implied. The spoke post on what a production injection mold costs breaks the price down by class and cavity count.
How many cavities should your mold have?
The right cavity count is the smallest number that makes your annual volume in the press time you can afford, because each cavity adds cost to the tool and takes cost off the part. Multi-cavity tools make 2 to 64 parts per cycle. At a 30 second cycle, one cavity makes 120 parts an hour and four make 480, so 500,000 parts a year takes more than 4,000 press hours in one cavity and about 1,040 in four.
Press size caps the count. Every cavity adds projected area, and clamp tonnage has to cover all of it. On presses under 200 tons, the kind Legacy Molding runs, a hand-held housing might go two or four cavities while a small clip could go 16 or more. Family molds put different parts in one tool, say a left and right housing half, and save a mold base and a setup, but every cavity has to fill and cool on the same shot, so the parts should be close in size and wall.
Should your mold have a hot runner or a cold runner?
A cold runner is cheaper to build and a hot runner is cheaper to run, and the crossover depends on your volume and your resin price. In a cold runner mold, the sprue and runner solidify with every shot and are ejected with the parts, then reground or thrown away. In a hot runner mold, heated manifolds and nozzles keep the melt molten right up to the gate, so nothing but the part comes out.
| Feature | Cold runner | Hot runner |
|---|---|---|
| Tool cost | Lower | Higher; manifold, nozzles, heaters and a controller |
| Material use | Runner scrap on every shot; regrind if the resin and spec allow | Near zero runner scrap |
| Cycle time | Runner is often thicker than the part and sets the cooling time | Shorter; only the part has to cool |
| Best fit | Low to mid volume, short runs, resins that regrind well | High volume, costly resins, thin small parts |
Plastics Technology’s hot runner tipping-point article shows how large the runner penalty can get: a 64-cavity cold runner mold making 2 gram parts on a 320 gram shot, so about 60 percent of every shot was regrind, with a hot runner projected to cut the cycle from 14 to 10 seconds. Most of Legacy Molding’s work sits well below that scale, and a cold runner with regrind is often right in the tens of thousands of parts. Above a few hundred thousand parts a year, or on an expensive resin, ask for both prices.
What does tooling cost, who builds it, and how is it kept alive?
Tooling costs what the class, cavity count, geometry, finish, steel and runner system add up to, and for most small to mid-size molders the steel is cut by a specialist mold shop rather than the molder. Legacy Molding’s published range is $3,000 for a simple single-cavity aluminum tool to $100,000 or more for complex multi-cavity hardened steel, with a Class 101 production mold typically $25,000 to $80,000. Lead time runs 2 to 4 weeks for a simple mold and 6 to 12 weeks from design approval to first article for a complex multi-cavity production mold.
How Legacy Molding handles it. Mold design and DFM review happen in-house in Phoenix, where Brent Hanke checks draft, wall, gate location and ejection before the design is released, because every fix at that stage is free and every fix in steel is not. A vetted tooling partner builds the tool, and it comes back to Phoenix for sampling, a first article inspection report with every dimension measured per cavity, and release to production. You own the mold, and Legacy Molding puts that in writing.
Here is a shipment Legacy Molding receives several times a year: a mold transferred from a molder that closed or fell behind, with no setup sheet, no last-shot samples and sometimes no drawing. The tool is inspected, cleaned, and checked for worn gates, stuck slides and plugged cooling lines, then sampled and measured in a first article before production starts. The post on how to transfer an injection mold without losing production walks through what to collect before a tool moves.
Maintenance is what gets a mold to its rated life. Ask your molder what the preventive maintenance interval covers: cleaning the parting line and vents, checking ejector pins, slides and lifters for wear, flushing cooling lines, inspecting gates and shut-offs, and logging every repair so the record travels with the tool. Flame retardants and glass fibers wear steel faster than a natural ABS, so a tool running them needs attention sooner. Legacy Molding maintains and repairs molds in Phoenix and keeps the record with the tool.
Tooling decisions, one at a time
Each of these choices gets its own post with a decision table.
- Hot runner vs cold runner molds
- Multi-cavity vs family molds
- Aluminum vs steel injection molds
- What a production mold costs
- How to move a mold to a new molder
Frequently Asked Questions
What is tooling in injection molding?
Tooling is the mold: the cavity and core that form the part, the mold base that holds them, the runner and gates that feed melt, the ejectors that push the part out, and the cooling lines that set cycle time. The word also covers slides, lifters and hot runner systems built into the mold.
How long does an injection mold last?
It depends on the class. An SPI/PLASTICS Class 101 hardened steel mold is rated for one million cycles or more, Class 102 for roughly 500,000 to one million, Class 103 for under 500,000, Class 104 for under 100,000 and Class 105 prototype tools for under 500. Abrasive resins, poor maintenance and a worn press all shorten that.
Who owns the injection mold, the customer or the molder?
The customer who pays for the mold normally owns it, but only if the quote and purchase order say so. Confirm ownership in writing, make sure the tool is tagged with your name, and keep the design files and maintenance records so the mold can move if it ever has to.
Conclusion
Three things to carry into your next tool quote. The mold class is a life rating, so size it to the whole program, not one year. Cavity count and runner type trade tool cost against part cost, and your volume decides the trade. And the steel, the class, the cavity count and the owner should all be written on the quote, never implied.
Legacy Molding designs molds and runs DFM in Phoenix, builds through vetted partners, and ships a first article report with every new or transferred tool. Moving a mold or starting a new one? Start with the tooling and transfer page, or call Brent Hanke at 480-256-9773.
Sources
- Plastics Industry Association (PLASTICS, formerly SPI), Customs and Practices of the Moldmaking Industry (AR-101, revised May 2023): https://www.plasticsindustry.org/data-report/customs-and-practices-of-the-moldmaking-industry/
- Plastics Technology, Running Cold to Hot: Tipping Point to Convert to a Hot Runner System (Derrick Hennebicque, 2021): https://www.ptonline.com/articles/running-cold-to-hot-tipping-point-to-convert-to-a-hot-runner-system
Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com
Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.
Have a part like this to quote?
Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.
