Blow Molding vs Injection Molding: Which Fits Your Part

Last Updated: October 28, 2026

Answer Capsule: Blow molding vs injection molding comes down to one question: is the part hollow? Blow molding inflates a hot tube of plastic inside a mold to make bottles, tanks and ducts with thin, open interiors. Injection molding fills a closed steel mold under pressure to make solid, detailed parts. Hollow means blow; solid or detailed means injection.

You have a hollow part, a reservoir, a float, a duct or a handle, and two quotes that do not line up. One molder calls it a blow molded part. The other wants to injection mold it in two halves and weld them. Blow molding vs injection molding is the first decision on that part, and it drives the tool price, the part price and the lead time.

The wrong call costs money either way. Pick blow molding for a part with threads and a tight bore, and you fight wall variation for years. Pick injection molding for a plain bottle, and you pay for two cavities and a welding step.

This guide covers how each process works, what each costs, which materials run in each, and when a hollow part should still be molded in halves. Legacy Molding is an injection molder in Phoenix and does not blow mold.

What is the difference between blow molding and injection molding?

Blow molding inflates a soft tube of plastic, called a parison, against the inside of a cooled mold. Injection molding forces melted plastic under high pressure into a closed cavity. One process shapes a skin from the outside. The other fills a solid shape from both sides.

Blow molding has three main forms. Extrusion blow molding pushes a parison out of a die, closes a mold around it, and blows it out. That is how HDPE milk jugs are made. Injection blow molding first molds a preform around a core pin, then blows it. Stretch blow molding adds a stretch rod, which is how PET soft drink bottles are produced. Plastics Technology’s blow molding section covers all three.

Injection molding has one basic form and many options. A screw melts pellets, a shot fills the cavity, the part cools, and the mold opens. Two-shot and insert molding are variations on that same shot. Legacy Molding runs all three on presses under 200 tons, which covers parts up to about the size of a hand-held housing.

The fastest test is to ask where the tool touches the part. In blow molding only the outside touches the tool. In injection molding every surface does.

Is blow molding cheaper than injection molding?

Blow molding is usually cheaper on tooling, and injection molding is usually cheaper per part on detailed work. Neither process is cheap in the abstract. Each is cheap for the parts it was built for.

Tooling. Blow molds see low pressure, so they are often cut from aluminum, while injection molds are usually tool steel. That alone tends to put a blow mold below an injection mold of the same size. For scale, Legacy Molding publishes mold ranges from $3,000 for a simple single-cavity aluminum tool to $100,000 or more for complex multi-cavity steel. A Class 101 production mold typically runs $25,000 to $80,000. Ask a blow molder for a matching quote rather than trusting a rule of thumb.

Per part. A blow molded bottle carries pinch-off flash that must be trimmed and reground. Its cycle depends on a thin wall cooling against one side of the tool. An injection molded part comes out finished, in a cycle measured in seconds, with little scrap on a hot runner tool. Legacy Molding’s published per-part range is $0.10 to $5 or more, and runs above 100,000 parts often reach pennies.

The breakpoint is a range. It moves with part size, wall thickness, cavity count and program length. The injection molding cost post works the amortization math at 5,000, 50,000 and 500,000 parts. The same math applies beside a blow mold quote.

Blow molding vs injection molding at a glance

Factor Blow molding Injection molding
Part type Hollow, thin skin, one open end or none Solid or shell, detail on all surfaces
Wall control Set by parison programming; varies around the part Set by the cavity; uniform within design limits
Inside surface Not touched by the tool Formed by the core; threads, bosses, ribs possible
Typical materials HDPE, PET, PP ABS, nylon, PC, PP, HDPE, acetal, TPE/TPU, 50+ resins
Tooling Often aluminum, lower pressure, lower cost Steel or aluminum; $3,000 to $100,000+
Secondary work Trim flash, regrind, leak test Usually none; assembly or pad printing if needed
Tolerances Looser on wall and inside dimensions Published standard plus or minus 0.005 in
Legacy Molding offers it No Yes, including overmolding, insert and two-shot

Which materials run in blow molding versus injection molding?

Blow molding leans on HDPE, PET and polypropylene, resins with enough melt strength to hold a parison without sagging. Injection molding runs almost any thermoplastic, including filled and engineering grades. The blow molder needs a tube that hangs in the air for a few seconds. The injection molder needs a melt that flows through a gate.

That matters when your part needs properties. A glass-filled nylon bracket, a flame-rated polycarbonate housing or a TPE grip is an injection molded part. The materials page lists the resin families Legacy Molding runs, and every job ships with the resin supplier’s material cert.

When should a hollow part be injection molded in halves and joined?

Injection mold the halves when the inside of the part has to be controlled, or when the part needs features a parison cannot form.

Here is a call Legacy Molding gets most months. A buyer has a small fluid reservoir with a threaded port, a mounting boss and a sensor pocket inside. The blow molder flagged the boss and the pocket. The buyer wants to know if it can be molded at all.

It can. Split it at the widest section, mold two halves with a tongue and groove at the joint, and join them. The options are ultrasonic welding, hot plate welding, spin welding for round parts, solvent bonding on ABS or PC, or snap fits with a gasket. Brent Hanke reviews the joint in the DFM pass, because the joint is where a two-piece hollow part leaks.

The trade-off is honest. Two halves means two cavities or a family mold, a welding fixture and a leak test. Blow molding does that in one shot.

If the inside needs nothing and the volume is high, blow molding wins. If it needs threads, ribs or a tight bore, mold it in halves. Follow the wall, draft and boss rules in the injection molding design guide.

Choose blow molding when, choose injection molding when

Choose blow molding when:

  • The part is a bottle, tank, duct, float or hollow handle with no inside features.
  • Wall thickness can vary and the inside surface does not matter.
  • The resin is HDPE, PET or PP and you need a light, leak-tight skin.

Choose injection molding when:

  • The part is solid, or a shell with ribs, bosses, snap fits, threads or text.
  • You need the inside surface and the wall held to a drawing.
  • The resin is an engineering grade, filled, flame rated or an elastomer.
  • The part needs overmolding, a metal insert or a second material.

Legacy Molding only runs the second column. If your part belongs in the first, say so on the quote request and you will get a straight answer.

Frequently Asked Questions

Can you injection mold a hollow part?

Yes, in two ways. You can mold the part in halves and join them by welding, bonding or snap fit. Or you can use gas-assist molding, which hollows thick sections with nitrogen during the shot. Molding in halves is the common path for small parts with inside features.

Is blow molding faster than injection molding?

Per part, injection molding is usually faster. The cycle is set by a thin uniform wall cooling in a closed steel mold, and there is no trim step.

What tolerances can blow molding hold compared to injection molding?

Blow molding holds the outside shape well and the wall and inside dimensions loosely, because the parison stretches to reach the tool. Injection molding controls every surface. Legacy Molding’s published standard tolerance is plus or minus 0.005 in, and plus or minus 0.002 in or better on critical dimensions.

Does Legacy Molding do blow molding?

No. Legacy Molding is a custom injection molder in Phoenix, Arizona, running presses under 200 tons with overmolding, insert and two-shot molding. If your part is a plain hollow container, a blow molder is the right fit and Legacy will say so. If it needs detail or an engineering resin, send the CAD for a DFM review.

Conclusion

Three takeaways. Blow molding makes hollow skins from the outside and wins on bottles, tanks and ducts in HDPE, PET and PP. Injection molding fills a closed mold and wins on solid or detailed parts, controlled walls and engineering resins. A hollow part with inside features is still an injection molded part, molded in halves and joined.

If your part lands on the injection side, Legacy Molding will review it for manufacturability and ship a first article inspection report with the first lot. Send your CAD and annual volume for a quote with DFM notes, or call Brent Hanke at 480-256-9773.

Sources

Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com

Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.

Have a part like this to quote?

Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.

Request a Quote

Similar Posts