Injection Molding vs Extrusion: Which Process Fits Your Part
Last Updated: November 2, 2026
Answer Capsule: Injection molding vs extrusion comes down to shape. Extrusion pushes melt through a die to make a continuous profile with one constant cross-section, then cuts it to length. Injection molding fills a closed mold to make a discrete part with ends, holes, bosses and snap fits. Molds cost more; dies cost less; per-part cost depends on volume.
Your part is long in one direction and the same shape all the way down. One supplier wants to extrude it. Another wants to mold it. The wrong call costs you a mold you did not need, or an extruded profile that goes to a machine shop for every hole and notch.
Injection molding vs extrusion is not a question of which process is better. It is a question of shape: does the cross-section change, what sits at the ends, how many do you need, and at what tolerance?
This guide covers where each process wins, what the tooling costs, which materials run in each, and when a profile part should be molded instead. Legacy Molding is an injection molder in Phoenix, not an extruder, so you get the honest version. That includes the parts Brent Hanke tells buyers to send to an extrusion house.
What is the difference between injection molding and extrusion?
Extrusion makes a continuous shape, and injection molding makes a discrete part. An extruder melts pellets with a screw and pushes the melt through a shaped die. The profile is cooled in a water bath or on a calibrator, pulled at a steady speed, and cut to length.
An injection molding press melts the same pellets and shoots the melt under high pressure into a closed steel or aluminum mold. The mold holds the shape while it cools, opens, and ejects a finished part. That part can have walls in every direction, holes, bosses, ribs and snap fits. The Plastics Industry Association (PLASTICS) draws the same line: molding builds complex shapes in one operation, and extrusion holds one cross-section over any length.
Rule of thumb: If you can draw the part as one 2D outline and say “make it this long,” it is a candidate for extrusion. If the ends matter, it is a molded part.
Which parts should be extruded, and which should be injection molded?
Extrude the part when its shape is the same from end to end and the ends are plain cuts. Mold it when the ends, faces or interior have features. Typical extruded parts are tubing, pipe, wire insulation, weather seals, window profiles, sheet, film, trim and channel. Typical molded parts are housings, brackets, caps, connectors and clips.
Gray-zone examples:
- A rail with mounting holes. Extrude it and drill the holes, or mold it if the holes have counterbores or bosses.
- A channel with end caps. Extrude the channel, mold the caps. This is the most common split Legacy Molding sees.
- A short tube with a flange. Mold it if it is short. Extrude it and add a molded flange if it is long.
| Question | Points toward extrusion | Points toward injection molding |
|---|---|---|
| Cross-section | Constant along the full length | Changes; walls in more than one direction |
| End features | Plain cut ends | Caps, flanges, holes, bosses, snap fits |
| Length | Long, often sold by the foot | Fits in a mold; a hand-held housing or bracket on presses under 200 tons |
| Hollow sections | Easy; tubing and multi-chamber profiles | Needs cores, slides, or two parts joined |
| Tolerances | Looser; die swell, drawdown and cooling move dimensions | Tighter; about plus or minus 0.005 in standard |
| Tooling | A die, lower cost | A mold, $3,000 to $100,000+ |
| Secondary work | Cut to length, often drilling or notching | Usually none; features are in the mold |
How does tooling cost compare between a die and a mold?
A mold costs more than a die, usually by a wide margin. A mold forms every surface of the part; a die forms only its outline.
Legacy Molding’s published mold ranges start at about $3,000 for a simple single-cavity aluminum tool. They reach $100,000 or more for a complex multi-cavity hardened steel mold. A Class 101 production mold rated for one million or more cycles typically costs $25,000 to $80,000. The full breakdown of injection molding cost explains what moves those numbers.
An extrusion die is a plate, or a set of plates, with the profile cut through it, plus sizing tooling downstream. As a general range, simple solid profile dies run in the low thousands of dollars. Hollow or multi-chamber profiles with calibrators run into the low tens of thousands.
The die is not the whole story. Extrusion dies need trials. The profile swells and draws down as the melt leaves the die. Plastics Technology’s profile die design guide puts drawdown at 25 to 40 percent for PP and LDPE, against 4 to 10 percent for rigid PVC.
Injection molding vs extrusion: which materials run in each?
Most thermoplastics run in both processes, but the grades differ. Extrusion grades have lower melt flow, so the profile holds its shape between the die and the cooling bath. Injection grades flow more easily to fill thin walls under pressure. The same resin family is sold in both grades, and they are not interchangeable.
Common extrusion materials are PVC, HDPE, LDPE, PP, ABS, polycarbonate sheet, nylon tubing and TPE seals. Common injection materials are the same families plus glass-filled nylon, PC/ABS, acetal, PEEK and Ultem. Filled resins can be extruded, but the fibers and the die wear make it a specialty. If your part needs glass-filled nylon or a flame-retardant PC, molding is the safer bet.
When should a profile part be molded instead?
Mold the profile part when the features cost more to add afterward than the mold costs up front. Here is a call Legacy Molding gets most months. A buyer has an extruded channel, 8 inches long. Every piece goes to a shop for two drilled holes, a notch and a deburr.
At 50,000 pieces a year, that secondary work is the largest line on the invoice. A two-cavity mold puts the holes and the notch in the part, and it pays for itself inside the first year. Legacy Molding runs that math in the DFM review. Brent Hanke will tell you when the answer is still “extrude it.”
Signs a profile part belongs in a mold:
- It needs holes, slots or bosses at fixed positions.
- The ends need caps, flanges, clips or a radius, not a saw cut.
- The length is under about 12 inches, and the part fits a press under 200 tons.
- You need a tighter tolerance than the extruder can hold after drawdown.
- The part count justifies a mold. The production injection molding in Phoenix page covers how volume sets the per-part price.
When is molding a long thin part a mistake?
Molding a long thin part is a mistake when the melt freezes before it reaches the end of the cavity, or when the press needed is far larger than the part deserves. Clamp tonnage scales with the projected area of the part. A long thin part has a lot of area for very little plastic.
Plastics Technology reported that a 1 meter long thin-walled profile needs a press of around 500 tons to mold the conventional way. A 2 meter part needs up to 1,500 tons. Legacy Molding’s presses are under 200 tons, so a part like that goes to an extruder.
Even where it fits, a long thin molded part fights you: high injection pressure, multiple gates with weld lines, and warp as it cools unevenly. If the part needs molded features at each end, the better design is often a short molded fitting on an extruded body.
Frequently Asked Questions
Is extrusion cheaper than injection molding?
Extrusion is cheaper to tool, because a die costs a fraction of a mold, and cheaper per foot for a simple profile. Injection molding is cheaper per part when the part needs features extrusion cannot make, because they are in the mold rather than in a secondary operation.
Can you injection mold a long thin part?
You can, up to a limit set by flow length and press size. Long, thin parts need high injection pressure and large clamp tonnage, and the melt can freeze before the cavity fills. A molder with presses under 200 tons, like Legacy Molding, will usually suggest extruding the body and molding the ends.
Can the same plastic be extruded and injection molded?
Yes, but usually not the same grade. Extrusion grades have lower melt flow and hold their shape out of the die; injection grades flow more easily to fill thin walls. Ask the supplier which grade you have before you assume a drop-in swap.
Which process holds tighter tolerances?
Injection molding does. Standard molding holds about plus or minus 0.005 in, and precision molding with tight process control holds plus or minus 0.002 in on critical dimensions. Extruded profiles move with die swell, drawdown and cooling, so their tolerances are looser.
Conclusion
Three things decide injection molding vs extrusion: whether the cross-section is constant, what the ends need, and how many parts you need at what tolerance. Extrusion wins on long, uniform profiles with low-cost dies. Injection molding wins when the features are in the part and the volume pays for the mold. The most common right answer is a split: extrude the body, mold the fittings.
If your part has ends that matter, send your CAD and annual volume for a quote with DFM notes →. Legacy Molding answers in 24 to 48 business hours. Questions? Call Brent: 480-256-9773.
Sources
- https://plasticsindustry.org/articles/injection-vs-extrusion-important-trends-in-plastic-manufacturing
- https://www.ptonline.com/articles/tooling-know-how-five-tips-on-profile-die-design
- https://ptonline.com/articles/new-low-pressure-process-molds-long-profiles-on-small-presses
Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com
Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.
Have a part like this to quote?
Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.
