Injection Molding Material Selection Guide: How to Pick the Right Resin

Last Updated: October 28, 2026

Answer Capsule: Injection molding material selection starts with the part’s job, not a resin name. Rank six things in order: operating environment (heat, chemicals, UV), loads (impact, stiffness, creep), regulatory needs (UL 94, FDA), appearance, cost per part and moldability. Pick the cheapest resin family that passes all six, then confirm the grade on the datasheet.

You have a part that works as a 3D printed prototype and a launch date. The drawing says “ABS or equivalent,” and that line is where molded parts go wrong.

The wrong resin cracks in the cold, creeps under a screw or yellows in the Arizona sun. Or it fails a flame test after the tool is cut. Switching resins after tooling usually means a new shrink rate and a reworked mold.

This injection molding material selection guide gives you a six-step method and a table of the resin families production molders run most. It covers the regulatory checks that trip up electronics and food contact parts, and the swaps that save money. It is the method Brent Hanke uses when a part comes into Legacy Molding for DFM review.

What are the six steps of injection molding material selection?

The six steps of injection molding material selection run in order. The first questions eliminate resins, and the last ones pick between the survivors. Start with the environment, not cost. Heat and chemicals remove whole families before price enters the picture.

  1. Environment. Temperature, chemicals, UV and moisture, and for how long.
  2. Loads. Impact, stiffness, fatigue life, and creep under a constant load.
  3. Regulatory. UL 94 flame rating, FDA food contact, biocompatibility, traceability.
  4. Appearance. Gloss, color match, clarity, texture, paintability.
  5. Cost per part. Resin price times part weight, plus cycle time.
  6. Moldability. Shrink, moisture, flow length and your wall thickness.

Callout: Write the six answers on the RFQ. A molder who reads “continuous 85 degrees C, isopropyl alcohol, UL 94 V-0 at 1.5 mm, black, 200,000 per year” can confirm a resin in a day. “ABS or equivalent” is a guess.

What will the part see in service?

The environment question removes more resins than any other, so answer it with numbers, not words like “warm” or “outdoors.” Four things matter.

Temperature. Compare the resin’s continuous service temperature to the hottest the part will get. Heat deflection temperature on a datasheet is a short-term bending test (ASTM D648), not a continuous rating. Covestro’s Makrolon 2405 polycarbonate datasheet lists 124 degrees C at 1.80 MPa. BASF’s Ultramid A3K nylon 66 datasheet lists 75 degrees C at 1.80 MPa dry, but 220 degrees C at the lighter 0.45 MPa load.

Chemicals. Amorphous resins such as PC and ABS craze and crack in many solvents, oils and cleaners, sometimes only under stress. Crystalline resins such as PP, HDPE, nylon and acetal resist most of them. List every fluid the part touches, including cleaners.

UV and weather. Unprotected ABS, PC and nylon yellow and lose impact outdoors. UV stabilized grades and carbon black help. If the part lives outside, say so on the RFQ.

Moisture. Nylon absorbs water, grows and softens. The Ultramid A3K datasheet lists 2.5 to 3.1 percent moisture at 50 percent humidity, and its tensile modulus falls from 3,000 MPa dry to 1,100 MPa conditioned.

Which resin family fits which job?

Each resin family has a job it does well and a weakness that rules it out. The table below is the short version Legacy Molding uses in DFM reviews. All of these run on presses under 200 tons in Phoenix, and the full list is on the injection molding materials page.

Family Type Strengths Watch out for
ABS Amorphous Tough, low shrink, paints and plates well, low cost; housings and covers Poor UV, limited heat, solvent sensitive
Polycarbonate (PC) Amorphous Very high impact, clear, good heat; lenses, guards, medical housings Stress cracks in solvents, scratches, notch sensitive
PC/ABS Amorphous PC impact at ABS cost and flow; electronics housings Lower heat than PC, needs UV protection outdoors
Nylon 6 and 66 Semi-crystalline Strong, wear and chemical resistant; gears, clips, brackets Absorbs moisture, higher shrink, needs drying
Glass-filled nylon Semi-crystalline Stiff, strong, holds heat, low creep; structural brackets Directional shrink and warp, abrasive on tooling, poor surface
Polypropylene (PP) Semi-crystalline Cheap, chemical resistant, living hinges; containers, lids High shrink, low stiffness, poor cold impact unless copolymer
HDPE Semi-crystalline Cheap, tough in the cold, chemical resistant; caps, liners High shrink, low stiffness, hard to bond or print on
Acetal (POM) Semi-crystalline Stiff, slippery, low creep; gears, bushings, snap fits Hard to bond or paint, limited UV, high shrink
TPE and TPU Elastomer Soft grips, seals, overmolds on rigid parts Creep and compression set, cost per pound
PEEK and Ultem (PEI) High performance Very high heat and chemical resistance; aerospace, medical Expensive, high melt temperatures, special tooling

Pick the family first, then the grade. Each family has flame retardant, UV stabilized, glass filled and food contact grades, each with its own datasheet, shrink and price. The cost side of resin choice is covered in Choosing the Right Plastic Resin for Injection Molding.

Does your part need a UL 94 rating or FDA compliance?

If the part sits in an electrical enclosure or touches food, yes. That requirement belongs in material selection, not in a note after the tool is cut. Both programs are grade specific and thickness specific.

UL 94 flammability. UL 94 rates how a plastic burns in a standard test. From least to most demanding for enclosures: HB (slow horizontal burn), V-2 (vertical burn stops within 30 seconds, flaming drips allowed), V-1 (same timing, no flaming drips), V-0 (burn stops within 10 seconds, no flaming drips), then 5VB and 5VA for a harsher flame. The rating is listed with the thickness it was tested at. Makrolon 2405, for example, carries HB at 2.7 mm and V-2 at 0.75 mm. If you need V-0, specify a V-0 grade at your wall thickness.

FDA food contact. Resins for food contact must be made from substances listed in FDA regulations such as 21 CFR Part 177 for polymers. The resin maker provides a letter stating which regulation a grade complies with, so ask for it before you tool. Legacy Molding ships a material cert from the resin supplier with every new job and keeps lot traceability, but the compliance claim itself comes from the resin maker.

Which material swaps save money without hurting the part?

The swaps that save money without hurting the part move down one step in cost inside the same property band. Each depends on the part, so treat these as questions, not answers.

  • Polycarbonate to PC/ABS or ABS. If the part does not need PC’s full impact or clarity, PC/ABS flows easier and costs less. Plain ABS goes one step further for indoor housings.
  • Glass-filled nylon to unfilled nylon or PP with ribs. Stiffness from geometry is cheaper than stiffness from fiber. A ribbed unfilled part also warps less.
  • Acetal to polypropylene. If a snap fit or lid does not slide or carry a sustained load, PP can do the job for far less.
  • PEEK to Ultem or glass-filled nylon. If the real need is 150 degrees C rather than 250, a cheaper high-heat resin may pass.

Do not swap for price alone. Every resin change changes shrink, so a swap after tooling means a tool adjustment and a new first article. Decide the resin before the mold is designed.

How does moldability change the choice?

Moldability changes the choice because a resin that passes the property checks can still fail on the press. It has to fit your part’s walls, flow length and tolerances. Three things to check with your molder:

  • Shrink and tolerance. Amorphous resins shrink under 1 percent and hold tighter tolerances. Crystalline resins often shrink 1.5 to 2.5 percent or more and vary with cooling. Makrolon 2405 lists 0.65 to 0.70 percent; Ultramid A3K lists 1.5 to 1.8 percent. The link between resin and tolerance is covered in Injection Molding Tolerances: What to Specify and What Tight Tolerances Cost.
  • Flow length and wall. Thin, long walls need an easy flowing grade. A stiff-flow PC in a 1 mm wall will short shot.
  • Drying. Nylon, PC and Ultem must be dried before molding. PP and HDPE do not.

Here is a call Legacy Molding gets most months. An electronics OEM has a handheld housing quoted in glass-filled nylon because the original engineer wanted stiffness. The overseas molder has fought warp and a rough surface for a year.

The DFM review shows the stiffness need is modest and the part stays indoors under 60 degrees C. The customer also wants a smooth painted finish.

The suggestion is PC/ABS with two added ribs. That removes the warp, the drying step and the tool wear, and it gives a surface that paints. Shrink changes, so the move happens at the new tool, with a first article on every cavity. That review takes a day and ends a year of fighting the wrong resin.

Frequently Asked Questions

What is the cheapest material for injection molding?

Polypropylene and HDPE are usually the cheapest per pound, and their low melt temperatures shorten cycle time. The cheapest resin per part is the one that passes the environment, load and regulatory checks at the lowest price.

Is nylon or polycarbonate stronger?

Polycarbonate has higher impact strength, especially in the cold. Nylon wears better, resists more chemicals and is stiffer when glass filled. Nylon softens as it absorbs moisture, so compare conditioned values, not dry ones.

How do you read a plastic datasheet for material selection?

Check the test method and condition next to every number. Tensile data comes from ASTM D638, impact from ASTM D256 and heat deflection from ASTM D648. Each is run on a standard bar at a listed load. For nylon, look for dry and conditioned columns.

Conclusion

Start injection molding material selection with the environment, then loads, then regulatory needs. Choose the family before the grade, check every number against its test condition, and lock the resin before the mold is designed.

Legacy Molding runs 50 plus thermoplastic resins in Phoenix and reviews the material choice on every part before tooling. Send your CAD and annual volume for a quote with DFM notes, include the six answers above, or call Brent at 480-256-9773.

Sources

Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com

Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.

Have a part like this to quote?

Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.

Request a Quote

Similar Posts