Warpage in Injection Molding: Why Parts Warp, How to Fix It

Last Updated: October 27, 2026

Answer Capsule: Warpage in injection molding is a part that bows, twists or cups because different areas shrink by different amounts as they cool. Semi-crystalline and glass-filled resins warp the most, since they shrink more and shrink unevenly with flow direction. Fixes start with cooling and pack, then the gate, then uniform walls and resin choice.

Your glass-filled nylon bracket measures flat on the drawing and rocks on the bench. That is warpage in injection molding. It is the defect most likely to survive every process change and come back on the next lot.

Warp is not a bad cavity. The steel is right; the part shrank unevenly on its way out of it.

Thick walls shrink more than thin ones. Hot areas shrink more than cold ones. Glass fibers shrink less along the flow than across it. Any of those differences bends the part.

This post covers how to confirm warp, why parts warp, which resins warp most, and the fixes in order. The shrink figures come from the Covestro and BASF technical guides. The fix order is how Brent Hanke works a warped part at Legacy Molding in Phoenix.

What does warpage look like, and how do you know it is warp and not a bad tool?

Warpage is a part that bows, twists or cups while the cavity itself measures true. Three checks separate warp from a mis-cut tool:

  • Compare the part to the steel. If the cavity is right but the part is out, the part moved after ejection.
  • Change cooling time. Warp changes when you cool longer or eject hotter. A wrong cavity does not.
  • Measure again in two days. Semi-crystalline parts keep shrinking after molding as crystals form. Covestro’s shrinkage guide calls this post-shrinkage.

What causes warpage in injection molding?

Parts warp because shrinkage is not uniform. If every region shrank by the same amount, the part would be smaller but the right shape. The root causes fall into the four buckets Legacy Molding checks on every warp review.

Bucket What causes or worsens warpage
Material Semi-crystalline resins, glass or mineral fill, high shrink grades
Process Short cooling time, mold halves at different temperatures, uneven pack pressure, gate freezing before pack is done, ejecting a hot part
Tool Cooling lines far from a thick area, one half cooled better than the other, gate at the wrong end
Design Wall thickness changes, ribs across the flow, long flat panels, features on one face only

The one-sentence version: the part warps toward the side or region that shrank the most, so every fix makes shrink more even.

Which resins warp the most?

Semi-crystalline and glass-filled resins warp the most, because they shrink more and shrink differently with direction. Covestro’s shrinkage whitepaper puts unreinforced amorphous resins such as polycarbonate and ABS under 1 percent linear shrink. Unreinforced semi-crystalline resins such as nylon and PBT run above 1 percent. Glass fiber cuts shrink along the flow far more than across it.

Resin (Covestro data) Shrink along flow Shrink across flow Warp tendency
Polycarbonate, ABS, PC/ABS, unfilled Under 1 percent Under 1 percent, close to along-flow Low
Nylon 6, unfilled About 1.0 percent About 1.2 percent Medium to high
Nylon 6, 30 percent glass About 0.2 percent About 0.8 percent High on long or flat parts

Those nylon figures are at one holding pressure and will differ with your wall and process. They come from ASTM D955 test bars, so your part needs its own first article. The materials page lists the resin families Legacy Molding runs.

How do you fix warpage, in order?

Start with cooling and pack, then mold temperature balance, then the gate and cooling layout, then the part and the resin.

  1. Extend cooling time and eject cooler. A part ejected hot keeps shrinking in open air with nothing to hold it.
  2. Balance the mold halves. The hotter half shrinks more, and the part bows toward it. BASF’s guide shows it on an acetal part: as the core-side temperature was lowered while the cavity side stayed fixed, the part’s bow reversed direction. Match the two halves first, then use a deliberate offset only to steer a known bow.
  3. Pack until the gate freezes, so the gate area and the end of fill shrink alike. Check gate seal by weighing parts.
  4. Adjust melt temperature within the window.
  5. Fix the cooling layout. Add or move lines near thick areas, and give the core side its own circuit. This is tool work.
  6. Move the gate. BASF recommends gating long parts lengthwise, so the flow and the fibers run one direction.
  7. Change the part or the resin. Make walls uniform, core out thick areas, or move to a low-warp blend with an amorphous phase.

Should you fixture a warped part?

Clamping a hot part flat on a fixture usually trades one problem for another. John Bozzelli warns in Plastics Technology that parts held in position while cooling develop even more residual stress. That stress can release later with heat or time.

A cooling fixture is a fair bridge for a short run while the tool or design gets fixed. Write it down as a temporary deviation.

Design rules that prevent warpage

Here is a call Legacy Molding gets most months. An engineer has a long, flat glass-filled nylon bracket with a center gate and a row of ribs across its width. Every part bows into a shallow arc. The fibers run outward from the center gate, so the ends shrink one way and the middle another.

Moving the gate to one end made the flow run the length of the part. That took most of the bow out on the next tool revision. Turning the ribs lengthwise and balancing water on both halves took the rest.

Rules that keep warp off your drawing:

  • Keep walls uniform and blend every change. The wall thickness post gives the ranges by resin and the rib and boss ratios.
  • Gate long parts at an end, so the flow and the fiber orientation run one direction.
  • Run ribs along the flow, and keep them at 50 to 60 percent of the wall.
  • Pick the resin for the geometry. A flat cover in glass-filled nylon will fight you; the same cover in PC/ABS may not.

The injection molding defects hub covers the other nine common defects. Legacy Molding reviews walls, ribs and gate location on every part before tooling.

When does warpage need a tool change, and what should you ask your molder?

Warpage needs a tool change when cooling time, pack and mold temperature balance are used up and the part is still out of tolerance. A cooling line change or a gate move is tool work. A wall or rib change is a drawing change followed by tool work.

Ask for the setup sheet before and after, the time between molding and measurement, and the shrink value the tool was cut to. A corrective-action note should name the cause, the change, the result measured at the same interval, and the tool revision if steel was cut. Brent Hanke keeps the setup sheet with the first article on every Legacy Molding tool. The settings that held a part flat are the ones the next run starts from.

Frequently Asked Questions

What causes warpage in injection molding?

Uneven shrinkage. Thick areas, hot areas and the across-flow direction in glass-filled resins shrink more than their neighbors. The difference bends the part.

Which plastics warp the least?

Unfilled amorphous resins such as polycarbonate, ABS and PC/ABS warp the least. Their linear shrink is under 1 percent and close to the same in every direction.

Can warpage in injection molding be fixed after molding?

Sometimes, with a cooling fixture or annealing, but both add stress or cost and neither is a production answer. The lasting fixes are cooling balance, pack, gate location, uniform walls and resin choice.

How long after molding should you measure a part for warp?

Measure at a fixed time after molding and write it on the inspection record. Semi-crystalline parts such as acetal and nylon keep shrinking for days.

Conclusion

Warp is uneven shrink, so every fix makes shrink more even. That means balanced cooling, full packing, a gate that sends flow one direction, uniform walls, and a resin whose shrink fits the geometry. Treat a fixture as a bridge, not a fix. Legacy Molding checks walls, ribs, gate location and resin choice against warp risk in DFM review on every part. Send your CAD and annual volume for a quote with DFM notes →

Sources

Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com

Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.

Have a part like this to quote?

Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.

Request a Quote

Similar Posts