Compression Molding vs Injection Molding: Cost and Volume

Last Updated: October 29, 2026

Answer Capsule: Compression molding vs injection molding splits on material and volume. Compression molding presses a measured charge of thermoset, rubber or composite into a heated open mold and cures it over minutes. Injection molding shoots melted thermoplastic into a closed mold in seconds. Thermosets, large thick parts and low volumes favor compression. Detailed thermoplastic parts at volume favor injection.

Your part is a phenolic handle, a fiberglass cover or a rubber seal, and the drawing says “compression molded.” Now the volume is climbing and the supplier is slow. Someone has asked whether the part could be injection molded in a thermoplastic instead. Compression molding vs injection molding is the question on the table. Guess wrong and you buy a tool you cannot use, or a part that softens in service.

The two processes are not two ways to make the same part. They start from different materials and run on different clocks. A thermoset cures and never remelts, while a thermoplastic melts, freezes and can melt again. That one fact drives most of the comparison.

This guide covers material, cycle time, tooling, part size and volume, and when a thermoset part can move to an engineering thermoplastic. Legacy Molding is a thermoplastic injection molder in Phoenix and does not compression mold.

What is the difference between compression molding and injection molding?

Compression molding places a weighed charge in an open, heated mold. The press closes and holds heat and pressure until the material cures. Injection molding melts pellets in a screw and injects the melt into a closed mold, where it cools and freezes. One process cures a chemical reaction; the other freezes a melt.

Compression molding is built for thermosets and composites. The Open University’s engineering notes describe it as restricted to thermoset polymers such as phenolic, urea and epoxy, often with fillers like glass or wood flour, with cure times of 0.5 to 3 minutes and pressures of 14 to 40 MPa. Sheet molding compound (SMC) and bulk molding compound (BMC), the glass-filled polyester compounds behind many electrical covers, run the same way, and so do many rubber parts.

Injection molding is built for thermoplastics. ABS, nylon, polycarbonate, polypropylene, acetal, TPE and about 50 other resins run on the presses at Legacy Molding. Thermosets can be injection molded too, on dedicated equipment, but that is a separate specialty and not one Legacy Molding offers.

Is compression molding cheaper than injection molding?

Compression molding is usually cheaper on tooling and more expensive per part. It wins at low volume and on large simple parts. Injection molding wins once volume climbs and the part needs detail. The gap comes from the tool and the clock.

The tool. A compression mold is a heated cavity and a punch. It has no sprue, no runner and often no side actions, because the charge is placed in the cavity, not pushed through a gate. The Open University notes put compression scrap at 2 to 5 percent, lower than injection molding, because there are no sprues or runners. An injection mold carries runners, gates, cooling and ejectors, and Legacy Molding’s published range is $3,000 for a simple single-cavity aluminum tool to $100,000 or more for complex multi-cavity steel.

The clock. A thermoset has to cure, and cure takes minutes. Plastics Technology has reported solid thermoset toilet seats running a 7-minute cycle, and a 3-minute cure for a BMC range handle. A thermoplastic part of similar wall runs in seconds. Legacy Molding’s published per-part range is $0.10 to $5 or more, with high-volume runs often reaching pennies.

Compression molding sells you a cheap tool and an expensive minute. Injection molding sells you an expensive tool and a cheap second.

The injection molding cost post walks through the amortization math at 5,000, 50,000 and 500,000 parts. Run it with a compression quote beside it and your breakpoint shows up as a range.

Compression molding vs injection molding at a glance

Factor Compression molding Injection molding
Materials Thermosets (phenolic, epoxy, urea, melamine, polyester SMC and BMC), rubber, composites Thermoplastics: ABS, nylon, PC, PP, HDPE, acetal, TPE/TPU, PEEK and Ultem on request
Cycle time Minutes; cure of 0.5 to 3 minutes plus load and unload Seconds to about a minute, set by wall and cooling
Tooling Heated cavity and punch, lower cost, no runner Closed mold with runner, gates, cooling and ejection; $3,000 to $100,000+
Part size Small to very large; published range about 0.1 to 15 kg Limited by tonnage; Legacy Molding runs presses under 200 tons
Wall thickness Thick walls common; about 3 to 6 mm typical Thin uniform walls; thick sections sink and slow the cycle
Detail Simple shapes; undercuts, small holes and side draws are hard Ribs, bosses, snap fits, threads, text, overmolding, inserts
Legacy Molding offers it No Yes

Can a thermoset part move to an engineering thermoplastic?

Often yes, when the part lives well below the thermoset’s temperature range. No, when the job depends on what thermosets do best. That means continuous heat, creep resistance under load, and flame or arc performance. Plastics Technology puts the thermoset case plainly: they are lower in price and deliver higher rigidity and heat resistance, especially above 200 F.

Where the swap usually works:

  • Covers, housings, knobs and handles that were compression molded only because volume was low at the time.
  • Stiff parts at moderate heat, where a 30 percent glass-filled nylon or PC/ABS meets the load.

Where it usually does not:

  • Continuous service above the heat deflection temperature of the resin. Check ASTM D648 HDT against the real service heat.
  • Sustained load at heat, where thermoplastics creep and a cured thermoset does not.
  • Electrical parts that rely on a phenolic’s arc and track resistance, or on a UL 94 V-0 or 5VA rating the new grade has not earned.

Brent Hanke’s rule on a conversion is to start with the datasheet, not the part. Pull the service heat, load and flame rating off the old drawing. Then find a thermoplastic that clears all three with margin. The materials page lists the families Legacy Molding runs, including PEEK and Ultem on request.

What does a conversion look like on the shop floor?

It starts with the wall, then the heat, then the tool. Here is a call Legacy Molding gets a few times a year. A buyer has a compression molded phenolic terminal cover. The supplier is retiring, volume has outgrown a minutes-long cycle, and the buyer wants it injection molded.

First, the wall. The phenolic part is thick because compression molding likes thick walls. A thermoplastic version wants a thinner uniform wall with ribs, so the geometry changes.

Second, the heat. If the cover sits near a bus bar, a flame-retardant glass-filled nylon or a hotter grade is the candidate. Call it out by its UL 94 grade name.

Third, the tool. A new mold is quoted with the cavity count set by the real volume. The first lot ships with a first article inspection report and the resin maker’s material cert.

When the heat or arc requirement is beyond a thermoplastic, Legacy Molding says so. The part stays in compression molding with a new thermoset molder.

Choose compression molding when, choose injection molding when

Choose compression molding when:

  • The material is a thermoset, rubber or fiber composite and the properties depend on it.
  • The part is large, thick walled and simple, with no undercuts or small holes.
  • Service temperature, creep or flame performance rule out thermoplastics.

Choose injection molding when:

  • A thermoplastic clears the temperature, load and flame requirements with margin.
  • The part needs ribs, bosses, snap fits, threads or a second material.
  • Volume is high enough that a cycle in seconds pays back the tool.
  • You want tight tolerances, a controlled finish and an FAI report with the first lot.

Frequently Asked Questions

Which is stronger, compression molded or injection molded parts?

It depends on the material, not the process. A glass-filled thermoset or SMC part is usually stiffer and holds up better at heat. A glass-filled nylon or polycarbonate molded part can match the stiffness at room temperature and often wins on impact. Compare ASTM D638 and D648 values at your service heat.

Can compression molding make complex parts?

Within limits. It handles large and thick shapes well, but the material does not flow far, so undercuts, small holes and side draws are hard. Injection molding forms them in the tool.

Does Legacy Molding do compression molding?

No. Legacy Molding is a thermoplastic injection molder in Phoenix, Arizona, with overmolding, insert and two-shot molding on presses under 200 tons. If your part has to stay a thermoset, a compression molder is the right fit. If it can convert, send the drawing and operating conditions for a DFM review.

Conclusion

Three takeaways. Compression molding cures thermosets, rubber and composites in a simple heated tool over minutes, and wins on low volume, large size and high heat. Injection molding freezes thermoplastics in a closed mold in seconds, and wins on detail, tolerances and volume. A thermoset part can move to an engineering thermoplastic when temperature, creep and flame requirements clear with margin.

If your part can make that move, Legacy Molding will check the datasheet against your service conditions and ship an FAI report with the first lot. Send your CAD and annual volume for a quote with DFM notes, or call Brent Hanke at 480-256-9773.

Sources

Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com

Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.

Have a part like this to quote?

Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.

Request a Quote

Similar Posts