Die Casting vs Injection Molding: Metal to Plastic Guide
Last Updated: October 30, 2026
Answer Capsule: Die casting vs injection molding is a weight, cost and performance decision. Die casting forces molten aluminum or zinc into a steel die for stiff, heat-tolerant parts. Injection molding fills a steel mold with a thermoplastic such as glass-filled nylon for parts that are lighter, cheaper and free of corrosion and machining. Convert when heat, stiffness and shielding allow it.
You have a die cast bracket or housing that works, and a target to take weight and cost out of the assembly. Someone has asked whether it could be molded in plastic. Die casting vs injection molding sounds like a simple swap. It is not; a part that was never redesigned for plastic fails in service or costs more than the metal it replaced.
Done well, a conversion cuts weight, deletes machining and plating, folds several metal pieces into one part, and ends corrosion as a failure mode. Done badly, it softens near heat, creeps under a bolt, or leaks electrical noise.
This guide shows where plastic beats zinc and aluminum, where it cannot, which resins make the common swaps, and how to qualify the new part. Legacy Molding is an injection molder in Phoenix and does not die cast.
What is the difference between die casting and injection molding?
Die casting injects molten aluminum, zinc or magnesium into a hardened steel die under high pressure. Injection molding injects a melted thermoplastic into a steel or aluminum mold under high pressure. The machines look alike. The materials and the parts do not.
Die casting makes a metal part. It is stiff, conducts heat and electricity, and holds up at temperatures that would melt a plastic. It usually leaves the die with flash to trim, holes to tap and surfaces to machine or plate.
Injection molding makes a plastic part. It is lighter, comes out of the mold finished, and molds in threads, snap fits and color. It never rusts. It is also less stiff, softer at heat, and an insulator unless filled or plated. Legacy Molding runs the plastic side on presses under 200 tons.
How much weight does metal to plastic conversion save?
Aluminum alloys sit near 2.7 g/cm3 and zinc die casting alloys near 6.6 to 7.0 g/cm3. A 30 to 50 percent glass-filled nylon sits roughly between 1.35 and 1.6 g/cm3. So the same volume of plastic weighs about half as much as aluminum and a fifth as much as zinc. Those are approximate datasheet figures; check your exact grades.
The catch is that the plastic part is rarely the same volume. It needs ribs or thicker walls to make up stiffness, so the real saving is less than the density ratio. Your CAD mass properties are the only number that counts.
Weight is one line on the sheet. Plastics Today reported a sand-cast aluminum transmission cover that moved to a 60 percent glass-filled nylon 4/6, molded complete in one step, deleting two machining operations.
Where can plastic not replace zinc or aluminum?
Plastic cannot replace a die casting when the part runs hot, creeps under a sustained load, needs metal stiffness in a fixed envelope, or has to shield or ground electronics. Those four limits decide most conversions.
- Heat. Check the ASTM D648 heat deflection temperature and the UL relative thermal index against the real operating temperature. BASF lists an Ultramid grade aimed at die-cast replacement with an RTI of 140 C and a UL 94 V-0 rating. Above that class of number you are into PEEK, Ultem or back to metal.
- Stiffness and creep. Aluminum’s modulus is roughly 69 GPa. BASF’s 40 percent glass-filled grade lists a tensile modulus above 13 GPa. You close the gap with ribs and section depth. A bolted joint under constant load needs a metal insert or a compression limiter.
- EMI and grounding. A plastic housing is transparent to electrical noise unless you use a conductive filled grade, plate it, or add a shield. Each adds cost.
- Thermal conductivity. Heat sinks stay metal.
Which plastics replace die cast parts?
Glass-filled nylon 6 and 66 are the most common swaps for aluminum and zinc. Polycarbonate and PC/ABS follow for housings that need impact and a good finish. PEEK and Ultem take the hot jobs.
| Die cast part | Common thermoplastic swap | Why it works | Watch for |
|---|---|---|---|
| Aluminum bracket or mount | 30 to 50 percent glass-filled nylon 66 | Stiff, tough, molds ribs and bosses in one shot | Moisture growth; creep at bolts; add inserts |
| Zinc housing with fine detail | PC, PC/ABS or glass-filled nylon | Finish, impact, molded-in color and text | Heat near electronics; EMI needs plating or fill |
| Aluminum cover or lid | Glass-filled PP or nylon 6 | Light, low cost, no corrosion | Lower stiffness; design for ribs |
| Hot or load-bearing part | PEEK or Ultem | Highest heat and stiffness among thermoplastics | Resin cost; may still lose to metal |
Legacy Molding runs 50 or more resins, including these nylons and polycarbonates, with PEEK and Ultem on request. The materials page lists the families. Where a thread or ground path has to stay metal, insert molding puts a brass or steel insert into the molded part.
How does tooling cost compare in die casting vs injection molding?
Both need a hardened steel tool, so the tooling line is often closer than buyers expect. The per-part line is where plastic pulls ahead.
For scale, Legacy Molding publishes mold costs from $3,000 for a simple single-cavity aluminum tool to $100,000 or more for complex multi-cavity steel. A Class 101 mold rated for a million or more cycles typically runs $25,000 to $80,000.
Ask your die caster for a matching quote. Then add what die casting carries after the tool: trimming, machining, tapping, plating, and the scrap from each. The injection molding cost post shows how the mold amortizes across volume.
Brent Hanke’s advice on a conversion quote: never compare tool prices alone. Compare the landed cost of a finished part at your annual volume, with every secondary operation on both sides counted.
What does the qualification path look like for a converted part?
The path is a new drawing, a DFM review, a first article inspection and your own functional test, in that order.
Here is a call Legacy Molding gets a few times a year. A quality manager has a die cast aluminum sensor bracket with machined-feature tolerances on the drawing. Engineering has redesigned it in glass-filled nylon with ribs and two brass inserts. How do they prove the new part?
First, a new drawing with plastic tolerances, because metal tolerances will not survive shrink and moisture. Legacy Molding’s published standard is plus or minus 0.005 in, with plus or minus 0.002 in or better on critical dimensions. Second, a DFM review of wall uniformity, rib ratios, draft, gate location and insert retention before any steel is cut.
Third, a first article inspection on the new tool. Every dimension on the ballooned drawing is measured per cavity, with the resin supplier’s material cert and lot number attached. Aerospace customers get AS9102 forms.
Fourth, your own functional tests at temperature and load. An FAI proves the part matches the drawing, not that the drawing was right.
Choose die casting when, choose injection molding when
Choose die casting when:
- Continuous operating temperature is above what an engineering thermoplastic holds.
- The part carries a sustained structural load in a space you cannot thicken or rib.
- The part must shield, ground or conduct heat and you cannot add plating or fill.
Choose injection molding when:
- Heat, load and shielding needs are inside a thermoplastic’s range with margin.
- Weight, corrosion or secondary machining is driving cost.
- Several metal pieces can become one molded part, and volume is high enough for a Class 101 mold to pay back.
Frequently Asked Questions
Is injection molding cheaper than die casting?
Per part, usually yes once the part is redesigned for plastic. The molded part skips machining, tapping and plating and weighs less. On tooling, the two are closer, since both need a hardened steel tool. Compare landed cost per finished part at your annual volume.
Can glass-filled nylon replace aluminum?
Often, for brackets, housings, covers and mounts that see moderate heat and load. A 30 to 50 percent glass-filled nylon 66 has roughly a fifth to a third of aluminum’s stiffness. The part needs ribs and deeper sections. Design around moisture absorption and creep under bolted loads.
Does Legacy Molding do die casting?
No. Legacy Molding is a custom injection molder in Phoenix, Arizona, running thermoplastics on presses under 200 tons with insert molding, overmolding and two-shot. If your part has to stay metal, a die caster is the right fit. If it can convert, send the current drawing and operating conditions for a DFM review.
Conclusion
Three takeaways. Plastic beats die casting on weight, corrosion, part consolidation and finished-part cost when heat, load and shielding allow it. Metal keeps the job when the part runs hot, carries sustained load in a fixed envelope, or has to shield or conduct. The qualification path is a new drawing, a DFM review, an FAI with a material cert, and your own functional test.
If your part can make the move, Legacy Molding will review the redesign and ship the FAI with the first lot. Send your CAD, the current drawing and annual volume for a quote with DFM notes, or call Brent Hanke at 480-256-9773.
Sources
- Plastics Today, High-glass nylon replaces aluminum: https://www.plasticstoday.com/plastics-processing/high-glass-nylon-replaces-aluminum
- BASF, Machinery parts made of Ultramid (metal replacement grades): https://plastics-rubber.basf.com/northamerica/en/performance_polymers/products/ultramid/machinery_parts_made_of_ultramid.html
Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com
Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.
Have a part like this to quote?
Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.
