Injection Mold Cost: What a Production Tool Costs in 2026
Last Updated: October 23, 2026
Answer Capsule: Injection mold cost runs from about $3,000 for a simple single-cavity aluminum tool to $100,000 or more for a complex multi-cavity hardened steel mold. A Class 101 production mold rated for one million or more cycles typically costs $25,000 to $80,000. Cavity count, part geometry, steel grade, surface finish and hot runners drive the price.
You have two mold quotes on your desk, one at $18,000 and one at $46,000, for the same part. Neither one explains the gap. One might be a short-life aluminum tool and the other a hardened steel production mold. Until you know what moves injection mold cost, you cannot tell.
That gap matters more than the part price. The mold is a one-time check you write before a single part ships. A tool built for the wrong volume either wears out early or ties up cash you did not need to spend. A quote with no itemization also hides the questions that bite later: who owns the steel, who pays for maintenance, and what happens when a cavity wears.
This guide gives you typical injection mold cost ranges by class and cavity count, the choices that move the number, and what a mold quote should itemize. Brent Hanke, owner of Legacy Molding in Phoenix, designs molds in-house and builds them through vetted tooling partners. The ranges below are the ones Legacy Molding publishes, not calculator output, and every quote is itemized.
How much does an injection mold cost?
A production injection mold costs between $3,000 and $100,000 or more, and the right number depends on how many parts the tool must make over its life. Legacy Molding quotes tools across that whole range. The first question is always annual volume, because volume sets the mold class.
| Tool type | PLASTICS (SPI) class | Rated life | Typical cost range |
|---|---|---|---|
| Prototype, aluminum or soft steel, single cavity | Class 105 | Under 500 cycles | From about $3,000 |
| Low-volume aluminum or pre-hardened steel | Class 104 | Under 100,000 cycles | Low end of the range; single cavity, soft steel |
| Medium-volume pre-hardened steel | Class 103 | Under 500,000 cycles | Middle of the range; cavity count sets it |
| Medium-to-high volume hardened steel | Class 102 | 500,000 to 1 million cycles | Approaches Class 101 pricing as cavities and hardness rise |
| High-volume hardened steel, multi-cavity | Class 101 | 1 million or more cycles | $25,000 to $80,000; $100,000 or more for complex tools |
The dollar figures are the ranges Legacy Molding publishes for parts that fit presses under 200 tons, roughly a hand-held housing or a bracket. A large part, a deep draw, or a tool with several side actions can push past the top of each range. Treat the table as a sanity check, not a quote.
Cycles are not parts. A four-cavity Class 103 tool rated for 500,000 cycles can make two million parts. Multiply cavities by rated cycles before you decide a class is too small.
What drives the price of a mold?
Seven things set injection mold cost: cavity count, part geometry, surface finish, mold steel grade, cycle time targets, material, and secondary operations. Every one of them is a choice you make before the first chip is cut. So every one is a place to save or to spend on purpose.
- Cavity count. More cavities mean more steel, more machining, and a bigger mold base. Tools make 2 to 64 parts per cycle, and each added cavity costs less than the first but never nothing.
- Part geometry. Undercuts need slides or lifters. Deep ribs need thin, hard steel. Threads may need unscrewing cores. Each mechanism is a line item.
- Surface finish. A polished lens finish or a textured cosmetic surface takes hours of hand work. A machined finish on a hidden part does not.
- Mold steel grade. Aluminum cuts fast and cheap. Pre-hardened P20 is the workhorse for mid-volume. Hardened H13 or S7, and stainless for corrosive resins, cost more to cut and heat treat.
- Cycle time. A tool built for a fast cycle needs more cooling lines, better venting, and sometimes a hot runner.
- Material. Glass-filled nylon wears steel. Clear polycarbonate needs a flawless polish. The resin you pick changes the steel you need.
- Secondary operations. Inserts, overmolding, or a texture applied after the tool is cut all add cost and lead time.
Ask every tool quote to list these seven items on separate lines. When two quotes differ by $20,000, the difference almost always lives in one or two of them.
Steel or aluminum: which one should you buy?
Buy aluminum when you need parts fast and expect under 100,000 cycles. Buy steel when the tool must run for years or the resin is abrasive. Simple aluminum tools come from Legacy Molding’s partners in 5 to 10 business days, but the cavity surface wears and the parting line flashes sooner.
| Factor | Aluminum tool | Pre-hardened steel (P20) | Hardened steel (H13, S7) |
|---|---|---|---|
| Rated life | Under 100,000 cycles | Up to about 500,000 cycles | 1 million or more cycles |
| Lead time | 5 to 10 business days (simple) | 2 to 4 weeks (simple), 6 to 12 weeks (complex) | 6 to 12 weeks |
| Cost | Lowest | Middle | Highest |
| Glass-filled or abrasive resin | Poor fit | Fair | Best |
| Repairable by welding | Limited | Yes | Yes |
Hardness tells you the class. PLASTICS Class 101 calls for cavities and cores hardened to at least 48 Rc and a mold base of at least 280 BHN. If a quote calls a P20 tool a Class 101, ask which part of the standard it meets. The injection molding tooling explainer walks through the steel grades and mold classes in more detail.
Hot runner or cold runner: does the extra cost pay back?
A hot runner pays back when the runner would otherwise waste expensive resin or stretch the cycle. That usually means multi-cavity tools at high volume. For a single-cavity tool making 20,000 parts a year, a cold runner is cheaper to build and simpler to maintain.
A cold runner mold solidifies the sprue and runners with the part each shot. That runner is scrap or regrind, and it adds material and cycle time. A hot runner keeps the melt channels heated, so only the part is molded. The trade is a higher tool price, a controller to buy, and more to go wrong at a tool transfer.
Run the math with your molder. Multiply runner weight by resin price by annual shots, then add the cycle time saved at the press rate. If that number beats the hot runner premium inside a year or two, buy the hot runner. Legacy Molding will quote both options when the volume is close.
Who owns the mold, and what should the quote say about it?
You own the mold when you pay for it, but only if the purchase order or tooling agreement says so in writing. Verbal ownership is how buyers end up paying a second time for their own steel when they try to move a tool.
Here is a situation Legacy Molding sees every few months. A buyer wants to transfer a tool from a molder that is winding down. The molder claims the tool because the invoice called it a “tooling fee” and the buyer only paid part of it. There are no drawings, no last-shot samples, and the hot runner controller is not included.
The transfer takes months instead of weeks. Put these items in writing before the tool is built:
- Ownership. The customer owns the mold, the cavity inserts, the electrodes and the tool drawings on final payment.
- Native files. Who keeps the mold CAD and whether you get a copy. Many tool builders treat the mold design as their own IP, so ask up front.
- Storage and release. Where the tool lives, and how fast it ships if you ask for it.
- Maintenance. Who pays for normal wear versus damage, and how cycles are logged.
- Engineering changes. How a design revision is quoted and who approves it.
Some states have molder’s lien laws that let a shop hold a tool when invoices go unpaid. Pay the tool invoice in full and keep the receipt with the ownership letter. The tooling and mold transfer page describes how Legacy Molding takes in a tool and qualifies it in Phoenix.
What should a mold quote itemize?
A mold quote you can compare lists the mold class, steel grade and hardness, cavity count, runner type, every side action, surface finish, lead time to first article, and exclusions. A single number with a lead time is not a quote. It is a guess you cannot check.
| Line item | What to look for |
|---|---|
| Mold class and rated cycles | Class 101 to 105, with the cycle count the builder stands behind |
| Steel grade and hardness | P20, H13, S7, stainless or aluminum, with Rc or BHN |
| Cavity count and layout | Number of cavities, family tool or dedicated |
| Runner system | Cold runner, or hot runner with drop count and controller included or not |
| Actions | Slides, lifters, unscrewing cores, each listed |
| Surface finish | PLASTICS finish grade or texture pattern number |
| Lead time | Weeks from design approval to first article samples |
| Sampling and FAI | Included or extra, and how many sample runs |
| Exclusions | Texture, controller, spare parts, design changes |
Mold life is a projection, not a warranty. As Plastics Technology puts it, a builder should never guarantee the longevity of a mold, because a tool is finished when the repair cost exceeds its worth. A tool that is cleaned, greased and checked on a schedule outlasts one that is not. Parting line flash that is ignored only gets worse. Ask what maintenance the molder performs and how it is recorded.
The full injection molding cost guide shows how to spread the tool cost across your annual volume to get a true per-part number.
Frequently Asked Questions
How much does a simple injection mold cost?
A simple single-cavity aluminum or soft steel mold for a small part typically costs $3,000 to $10,000. It is built for prototype or low-volume use, under 100,000 cycles at best, and ships in days to a few weeks. If the part has undercuts, threads or a cosmetic finish, the price climbs quickly.
How long does an injection mold last?
A hardened steel Class 101 mold is rated for one million or more cycles. Class 102 is rated for 500,000 to one million, Class 103 for under 500,000, and Class 104 for under 100,000. Actual life depends on the resin, the maintenance, and how hard the tool is run, so treat the rating as a projection.
Why does mold cost vary so much between quotes?
Quotes differ because builders assume different mold classes, steel grades, cavity counts and runner systems for the same part. An $18,000 quote might be a P20 cold runner tool, and a $46,000 quote might be hardened steel with a hot runner. Ask both builders to itemize the same list, and the gap usually explains itself.
Do I own the injection mold if I paid for it?
In most cases, yes, but only if the purchase order or tooling agreement states it and the tool is paid in full. Get ownership of the mold, inserts and drawings in writing before the build starts. Without that letter, moving the tool to another molder can turn into a dispute.
Conclusion
Three takeaways. Injection mold cost tracks the mold class, so decide how many parts the tool must make before you ask for a price. Cavity count, steel grade, surface finish and runner type explain most of the gap between quotes, so ask for them itemized. Ownership belongs in writing, with the drawings and the controller named.
A tool built for the right class, with the right paperwork, is the cheapest part of a molding program over its life. Legacy Molding designs molds in-house, builds through vetted partners, and ships a first article with every new tool from its Phoenix shop.
Send your CAD and annual volume for a quote with DFM notes, or call Brent at 480-256-9773.
Sources
- Plastics Technology, “How Many Parts Will My Mold Make? Part 1”: https://www.ptonline.com/articles/how-many-parts-will-my-mold-make-part-1
- PlasticsToday, “The design is mine: Moldmakers speak out on who owns the IP”: https://www.plasticstoday.com/injection-molding/-the-design-is-mine-moldmakers-speak-out-on-who-owns-the-ip
Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com
Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.
Have a part like this to quote?
Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.
