Flow Lines in Injection Molding: Causes and How to Fix Them

Last Updated: October 25, 2026

Answer Capsule: Flow lines in injection molding are wavy rings, ripples or tone changes on the part surface, usually near the gate or at a wall change. They form when the melt front slows and cools as it fills. Most clear with a hotter mold, faster fill and a larger gate; the rest need wall and gate design changes.

Your inspector just rejected a lot of textured ABS covers for “ripples near the gate,” and the molder says the parts are in spec. Both can be right. Flow lines in injection molding are a cosmetic defect. They matter only where the drawing says the surface matters.

Flow lines still cost money. They trigger sorting, arguments over cosmetic limits, and longer cycles. Most trace back to a melt front that stalled and cooled on its way across the cavity.

This post covers how to tell flow lines from their look-alikes, why they form, and the fixes in the order a molder tries them. The cause list follows the BASF troubleshooting guide. The fix order is how Brent Hanke works a flow line complaint at Legacy Molding in Phoenix.

What do flow lines look like, and how do you tell them from splay, weld lines and burn marks?

Flow lines are concentric or parallel ripples that run across the direction of flow, like the grooves on a record. They sit near the gate or where the wall changes. Molders call them record grooves, ripples or wave marks.

The look-alikes each have a tell:

  • Splay is silver streaks that run with the flow and often move shot to shot. Moisture is the usual cause, covered in the splay post.
  • Weld lines are single straight seams downstream of a hole, boss or pin.
  • Burn marks are brown or black spots at the end of fill or in a blind rib.
  • Jetting is one snake-like strand from the gate, not rings around it.

What causes flow lines in injection molding?

Flow lines form when the melt front slows and its skin cools and thickens before the rest of the shot presses it against the steel. BASF’s troubleshooting guide describes the mechanism. The front cools because the flow rate drops, and the frozen skin grows into parts of the front not yet touching the wall. Rising pressure can no longer press those areas flat, so the surface records every hesitation.

Here are the causes in the four buckets Legacy Molding checks on every defect review.

Bucket What causes or worsens flow lines
Material Stiff, high-viscosity grades; resin run at the cold end of its window
Process Low mold temperature, low melt temperature, slow or stepped injection speed, fill stage limited by pressure, early switch to hold
Tool Small gate, small runner or nozzle orifice, no cold slug well, cold spot in the steel near the gate
Design Sudden wall changes, thick walls at the end of the flow path, sharp corners, long thin flow paths

How do you fix flow lines, in order?

Start with temperature and speed, then the gate and runner, then the part.

  1. Raise mold surface temperature. A warmer cavity keeps the skin thin to the end of fill.
  2. Fill faster, and make sure the machine is in velocity control. John Bozzelli’s rule in Plastics Technology is that hydraulic pressure during first-stage fill should run 200 to 400 psi below the set limit.
  3. Raise melt temperature a step at a time within the window.
  4. Switch to hold later so the front is pressed to the wall while it is still soft.
  5. Open the gate, runner or nozzle. BASF lists pressure loss in the gating system as a cause, with larger gate diameters as the fix.
  6. Add or clean a cold slug well so the cold nose of each shot stays out of the cavity.
  7. Change the part. Blend wall transitions, radius corners and gate into the thickest section.

What is a cold slug, and why does it look like a flow line?

A cold slug is the small plug of melt that froze in the nozzle tip between shots and rides in at the front of the next shot. If nothing catches it, the plug enters the cavity first and leaves a dull patch or a short arc near the gate. The tool fix is a cold slug well, a pocket at the end of the sprue and at each runner turn that traps the plug.

A mark that shows only on the first shot after a pause is almost always a cold slug, not a true flow line.

The design rules that prevent flow lines

Here is a call Legacy Molding gets most months. A buyer has a textured polypropylene housing with a flat lid that steps down to a thin lip. The lip shows ripples on every part. A hotter mold and a faster fill helped but never cleared it.

The real cause was the step. The front slowed when it hit the thin lip, cooled, then surged. Blending the step with a taper and a radius cleared the ripples on the next tool revision.

Rules that keep flow lines off your drawing:

  • Keep walls uniform and blend any change with a taper and a radius.
  • Gate into the thickest section so the melt runs thick to thin, and avoid thick sections at the end of fill.
  • Round sharp corners. A corner stalls the front for an instant, and the surface records it.
  • Spec the cosmetic surface on the drawing. A deeper texture hides faint lines a polish would show.

The injection molding design guide covers the wall, transition and gate rules Legacy Molding checks in DFM review. The injection molding defects hub shows how flow lines relate to the other nine common defects.

When do flow lines need a tool change?

Flow lines need a tool change when the process window is used up and the mark still shows on a surface that matters. The signs: mold temperature is at the top of the resin’s range, the mark sits at a wall step or a sharp corner on every shot, or fill cannot be sped up without flash or burn. A gate or a cold slug well is a small cut; a wall step may mean welding and re-cutting the cavity. Either way, ask for samples at the old and new settings and a fresh first article.

What to ask your molder about flow lines

Ask for the short-shot study, the setup sheet before and after, and the cosmetic standard the parts were judged against. A corrective-action note should state the cavity and location with a photo under the same light, the settings before and after (mold and melt temperature, speed profile, switch-over point, pack pressure and time). Brent Hanke keeps the setup sheet with the first article on every Legacy Molding tool, so the settings that cleared a flow line are the ones the next run starts from.

Frequently Asked Questions

Are flow lines in injection molding a structural problem or just cosmetic?

Flow lines are cosmetic. They do not weaken the part the way a weld line can. They warn that the melt front is cooling early.

What is the difference between flow lines and weld lines in injection molding?

Flow lines are ripples across the flow near the gate or a wall change. A weld line is a single seam where two fronts met behind a hole or boss, and it can be a weak point.

Does a higher mold temperature always fix flow lines?

It is the most common fix but not the only one. If the gate is too small or the wall steps sharply, the front still stalls. Then the fix is the gate or the part.

Can flow lines be hidden with texture?

Often, yes. A medium or deep texture breaks up the light that shows a faint line. It does not fix the cause, so agree on the cosmetic limit before you rely on it.

Conclusion

Flow lines are the surface recording a melt front that stalled and cooled. Mold temperature and fill speed fix most of them, a larger gate or a cold slug well fixes the next group, and uniform walls with blended transitions prevent the rest. Agree on the cosmetic standard before the tool is cut, so a rejected lot is a measured call and not an argument. Legacy Molding checks wall transitions and gate location in DFM review on every part. Send your CAD and annual volume for a quote with DFM notes →

Sources

Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com

Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.

Have a part like this to quote?

Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.

Request a Quote

Similar Posts