Injection Molding Wall Thickness, Ribs and Bosses: The Design Rules
Last Updated: November 1, 2026
Answer Capsule: Injection molding wall thickness should be uniform and as thin as the part’s strength and flow allow, usually 1 to 4 mm depending on resin. Hold ribs and boss walls to 50 to 60 percent of the wall, keep ribs no taller than three times their base, and core out thick sections to avoid sink and warp.
A sink mark on the show surface, right over a screw boss, gets a molded part rejected at incoming inspection. It is also the easiest defect to prevent, because it was designed in before the tool was cut.
Thick sections, fat ribs and bosses merged into side walls cool slower than the wall around them. The shrinking core pulls the surface in. The same mistake causes warp, voids and long cycles.
This post gives you the injection molding wall thickness rules a production molder checks on every part. It covers the wall range by resin, rib and boss proportions, and how to core out thick sections. The figures come from resin maker design guides and from what Brent Hanke sees in DFM review at Legacy Molding in Phoenix.
What is the right injection molding wall thickness?
The right injection molding wall thickness is the thinnest uniform wall that gives the strength, stiffness and flow length the part needs. For most resins that lands between about 1 and 4 mm (0.040 to 0.160 in). Thinner walls cool faster and shrink less. Thicker walls fill longer flow paths, but they add sink, warp and cycle time.
Common molder design guides publish ranges like these. Treat them as starting points, because flow length and part size move the number.
| Resin | Typical nominal wall range |
|---|---|
| ABS | 1.1 to 3.5 mm (0.045 to 0.140 in) |
| Polycarbonate | 1.0 to 3.8 mm (0.040 to 0.150 in) |
| Nylon | 0.8 to 3.0 mm (0.030 to 0.115 in) |
| Polypropylene | 0.9 to 3.8 mm (0.035 to 0.150 in) |
Thin and thick both have limits. Covestro’s part and mold design guide treats walls under 1.5 mm as thin-wall molding, which may need higher pressure and a high flow grade. At the other end, a medium viscosity polycarbonate has a critical thickness near 3/16 in (4.8 mm), above which impact behavior turns brittle.
Why does uniform wall thickness matter?
Uniform wall thickness matters because every design-driven molding defect starts at a change in thickness. Thick sections cool last. When their core shrinks after the skin has set, the surface pulls inward (sink) or a hollow opens inside (void). A thick section next to a thin one also shrinks more, and the difference bends the part (warp).
Thick sections also keep moving after molding. In a Plastics Technology column on dimensional stability, Michael Sepe notes that thin amorphous parts settle in about 15 minutes. Thick semi-crystalline parts take hours.
Covestro’s guide gives a practical allowance. Low-shrink amorphous and filled resins can tolerate nominal wall variations up to about 25 percent without serious filling, warp or appearance problems. Unfilled crystalline resins can tolerate about half that. So a 2 mm ABS wall can run 1.5 to 2.5 mm, while a 2 mm polypropylene wall should stay nearer 1.75 to 2.25 mm.
When the thickness has to change, blend or taper the step instead of cutting a sharp shoulder. Gate into the thick section so the melt flows from thick to thin. At corners, make the outside radius one wall thickness larger than the inside radius so the corner stays uniform.
Callout: Uniform wall is the one rule that pays three times: shorter cycle, less sink and warp, and a tighter tolerance. If you change one thing after a DFM review, make it the wall.
How thick and how tall should ribs be?
A rib should be 50 to 60 percent of the wall it sits on and no taller than about three times its base thickness. Space ribs at least two wall thicknesses apart.
Covestro’s guide puts numbers on it: for polycarbonate and PC/ABS, a rib at 50 percent of the wall gives minimal sink on the opposite surface. A rib at 66 percent gives slight sink. For high gloss surfaces it drops the rib to 40 percent. Filled grades tolerate thicker ribs, 60 percent for minimal sink and 75 percent for slight sink, because they shrink less.
The rest of the rib rules from the same guide:
- Height. Limit rib height to about three times the rib base thickness.
- Draft. At least 0.5 degree per side so the rib releases.
- Base radius. About 0.125 times the rib thickness. A sharp root concentrates stress; a big radius adds a thick spot and sink.
- Spacing. At least two wall thicknesses between ribs so the steel between them can be cooled.
- Thin walls. On walls of 1.0 mm or less, the rib can equal the wall, because there is not enough material to sink.
Ribs are where draft most often gets missed. The rules for that are in Injection Molding Draft Angle: Rules by Material, Depth and Texture.
How do you design a boss that does not sink or crack?
Design a boss like a hollow rib. Hold the same 50 to 60 percent wall ratio and an outside diameter of 2.0 to 2.4 times the screw diameter. Radius the base and stand it off the side wall. A boss is the thickest feature on most parts, and it sits under a screw that loads it.
Covestro’s boss guidelines:
- Outside diameter of 2.0 to 2.4 times the outside diameter of the screw or insert.
- Hole diameter for a thread cutting screw in polycarbonate about 0.88 times the screw diameter. Check the screw maker’s chart for other resins.
- Boss wall to nominal wall held to the same ratio as the rib table. If it must be thicker, add a recess around the base on the outside surface to reduce the sink.
- Base radius of about 0.015 in as a compromise between strength and sink.
- Core the hole to the base wall level, so the base is not a solid slug.
- Keep bosses off side walls. Stand the boss off and connect it with a thin rib.
- Gussets at one-half to two-thirds of the wall, with draft and a radius, for bosses under a bending load.
- Tall bosses, more than five times their outside diameter, fill poorly. Split them into two shorter mating bosses.
How do you core out a thick section?
Core out a thick section by removing material from the back side until the remaining wall matches the nominal wall. Then add ribs if the section needs stiffness back. A solid block or a cast-metal shape converted straight to plastic is where sink and voids live.
Three ways to do it, in order of preference:
- Core from the back. A pocket on the non-cosmetic side leaves a uniform skin on the show face.
- Replace the mass with ribs. Two or three ribs give most of the stiffness at a fraction of the cooling time.
- Split the feature. A tall boss becomes two mating bosses. A long solid post becomes a tube with a cross rib.
Keep inside corners rounded. Covestro’s guide notes that stress at an inside corner climbs sharply once the radius to thickness ratio drops below about 0.2. So a 2 mm wall wants an inside radius of at least 0.4 mm. The complete set of feature rules is in the Legacy Molding injection molding design guide.
What goes wrong when the wall rules are skipped?
When the wall rules are skipped you get sink, warp, voids, short shots and a longer cycle. All five trace back to a thickness change the design could have avoided. The cause and fix for each are in Injection Molding Defects: Causes and Fixes for the 10 Most Common.
Here is a call Legacy Molding gets most months. A buyer is moving a tool from a molder that closed. The parts have always had sink over the four screw bosses and a slight bow across the lid.
The DFM review on the incoming tool shows bosses merged into the side walls with solid bases. The lid wall steps from 2 mm to 4 mm at the hinge. Legacy Molding inspects the tool, samples it as received, and runs a first article as a baseline. The recommendations: core the boss bases to the wall level, recess each boss on the outside, and taper the hinge step.
Those are small cuts on the existing steel, not a new tool. A second first article confirms the sink is gone and the cycle drops. That is why Legacy Molding reviews the part before quoting the mold.
Frequently Asked Questions
What is the minimum wall thickness for injection molding?
Most resins mold well down to about 0.8 to 1.0 mm (0.030 to 0.040 in) on small parts with short flow paths. Walls under 1.5 mm count as thin-wall molding and may need a high flow grade. Confirm the number with your resin maker’s guide and your molder.
Can an injection molded part have different wall thicknesses?
Yes, within limits. Amorphous and filled resins tolerate about 25 percent variation in nominal wall, and unfilled crystalline resins tolerate about half that. Blend every transition and gate into the thick section.
Why do ribs cause sink marks?
A rib adds material where it joins the wall, so that junction cools last and pulls the opposite surface inward as it shrinks. Keeping the rib at 50 to 60 percent of the wall keeps the sink too small to see.
How thick should a screw boss be in injection molding?
Size the boss outside diameter at 2.0 to 2.4 times the screw diameter. Hold its wall to 50 to 60 percent of nominal wall, like a rib. Core the hole to the base wall, radius the base and keep the boss off side walls.
Conclusion
Keep the wall uniform and in the 1 to 4 mm range for your resin. Hold ribs and boss walls to 50 to 60 percent of that wall. Core out anything thicker. Those three rules remove most sink, warp and void problems before the tool is cut.
Legacy Molding checks every one of them in the DFM review that comes with each quote. Every new or transferred tool ships with a first article inspection report. Send your CAD and annual volume for a quote with DFM notes, or call Brent at 480-256-9773.
Sources
- Covestro, Engineering Polymers: Part and Mold Design, Thermoplastics, A Design Guide, https://solutions.covestro.com/-/media/covestro/solution-center/brands/downloads/imported/1557214249.pdf
- Plastics Technology, Dimensional Stability After Molding, Part 1 (Michael Sepe), https://www.ptonline.com/articles/dimensional-stability-after-molding-part-1
Brent Hanke | Legacy Molding | 480-256-9773 | b.hanke@legacy-molding.com
Brent Hanke is the owner of Legacy Molding, a custom plastic injection molder in Phoenix, Arizona, producing parts for OEMs across the Southwest and the country.
Have a part like this to quote?
Send the CAD and annual volume. A Phoenix engineer replies within one business day with pricing and DFM notes.
